Use the same memory layout as we use for the NAND boot on the other boards.
QSPI flashes are present on the following boards:
sama5d2_xplained RevB: 32 Mbyte flash (mx25l3273fm2i-08g)
sama5d2_xplained RevC: 8 Mbyte flash (sst26vf064b-104i/sn)
sama5d27_som1_ek: 8 Mbyte flash (sst26vf064b-104i/sn)
sama5d2_ptc_ek: 8 Mbyte flash (sst26vf064b-104i/sn)
The 8 Mbyte limit is enough to cope with the memory layout used in the NAND
boot. rootfs exceeds the 8 Mbyte limit and will stay in eMMC in the
sama5d2_xplained case. The final scope is to use a single memory layout for
all boot medias.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@microchip.com>
[tudor.ambarus@microchip.com: change memory layout, add commit message]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Fix the following:
- use "jedec,spi-nor" binding, we use jedec compatible flashes
- set bus width to 4, we use quad capable flashes
- differentiate bewteen data and clk and cs pins
- drop partions as we don't use them in u-boot.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@microchip.com>
[tudor.ambarus@microchip.com: use "jedec,spi-nor", edit commit message]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
We have a macronix spi-nor flash on sama5d2_xplained RevB and
a sst spi-nor flash on RevC. Select the rest for testing purposes.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Backport the driver from linux v5.1-rc5 and adapt it for u-boot.
Tested on sama5d2_xplained Rev B with mx25l25635e spi-nor flash.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The watchdog of mediatek chips is enabled by bootrom before u-boot is
running. Previously we choose to enable the wdt driver only to disable the
watchdog hardware.
Now wdt service is enabled by default. The function arch_misc_init which is
only used to disable wdt is no longer needed.
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The initr_watchdog is currently placed before initr_serial. The
initr_watchdog calls printf and printf finally calls ops->putc of a serial
driver.
However, gd->cur_serial_dev points to a udevice allocated in board_f. The
gd->cur_serial_dev->driver->ops->putc points the the code region before
relocation.
Some serial drivers call WATCHDOG_RESET() in ops->putc. When DM is enabled
for watchdog, watchdog_reset() is called. watchdog_reset() calls get_timer
to get current timer.
On some platforms the timer driver is also a DM driver. initr_watchdog is
placed right after initr_dm, which means the timer driver hasn't been
initialized. So dm_timer_init() is called. To create a new udevice, calloc
is called.
However start from ops->putc, u-boot execution flow is redirected into the
memory region before relocation (board_f). In board_f, dlmalloc hasn't
been initialized. The call to calloc will fail, and this will cause DM to
print out an error message, and it will call printf again, causing
recursive error outputs.
This patch places initr_watchdog after initr_serial to solve this issue.
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Tested-by: Suniel Mahesh <sunil.m@techveda.org>
One of the SD-CARD slots on the Wandboard Quad B1 is MMC 2. Enable it as a
boot device.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
set_pwm() will always fail with -ENOSYS if pwm_ops set_invert() is
not implemented, leaving the backlight dark. Fix this by returning
no error if set_invert() is not implemented and no polarity change
is requested.
Fixes: 57e7775413 ("video: backlight: Parse PWM polarity cell")
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
With commit 06985289d4 ("watchdog: Implement generic watchdog_reset()
version") the init sequence has changed in arch_misc_init(), resulting
in a re-appearance of the d-cache issue on MT7688 boards (e.g. gardena).
When this happens, the first (or sometimes later ones as well) TFTP
command hangs and does not complete correctly. This leads to the
assumption that the d-cache is not in a clean state once the ethernet
driver is called (d-cache is used here for the buffers). The old work-
around with the cache flush somehow does not work any more now with
the new code change.
Unfortunately adding CONFIG_SYS_MALLOC_CLEAR_ON_INIT also did not fix
this issue. With v2019.07-rc3 it shows again. The time of accessing
the data seems to be very important here. It needs to be "very late"
in the boot process.
Testing has shown, that copying a 64KiB area in DDR at a very late
bootup time, directly before calling into the prompt, fixes this issue.
Flushing of the complete d-cache does not seem to necessary, as this
copy alone seems to fix this problem.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
dwc3-generic has been broken since MISC uclass has been modified to scan DT
sub-nodes after bind.
Fixing it by a using the no-op uclass.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This uclass is intended for devices that do not need any features from the
uclass, including binding children.
This will typically be used by devices that are used to bind child devices
but do not use dm_scan_fdt_dev() to do it. That is for example the case of
several USB wrappers that have 2 child devices (1 for device and 1 for
host) but bind only one at a any given time.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The EHCI iMX6 driver is only partly converted to DT probing and
still uses a tremendous amount of hard-coded addresses. Worse,
the driver uses hard-coded SoC-model-specific base addresses, which
are derived from values protected by SoC-specific macros, hence the
driver is also compiled for a specific SoC model. Even worse, the
driver depends on specific sequential indexing of the controllers,
from which it derives offsets in the PHY and ANATOP register sets.
However, when the driver is probed from DT, the indexing is not
correct. In fact, each controller has index 0. This patch derives
the index for DT probing case from the controller base addresses,
which is not the way this should be done, however it is the least
intrusive approach, favorable this close to release.
The necessary steps to convert this driver fully to DT probing are
described inside the patch, however this should be done in the next
release and depends on iMX clock driver patches.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Abel Vesa <abel.vesa@nxp.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
Commit b238e4b00c ("rockchip: Cleanup of make_fit_atf.py.") set
firmware = "atf_1";
loadables = "uboot","atf_1","atf_2";
Actually it should be:
firmware = "atf_1";
loadables = "uboot","atf_2","atf_3";
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
After the conversion to DM the U-Boot proper binary name
is 'u-boot-dtb.img', so adjust it accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
After the transition to DM, only the mx6dl/solo wandboard
is supported.
Add FIT image support so that all the wandboard variants
can be supported, like it was prior to the DM conversion.
Successfully booted Linux on mx6q/solo/qp wandboards.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Place dtbs under SoC level rather than board level.
imx6q-novena.dtb and imx6dl-wandboard-revb1.dtb were
placed under the board config option, so move them
to SoC level.
This also aligns with the kernel dts Makefile format.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The raw u-boot.bin for tinker board has been about 450KB without
debug option, and 550KB with all debug on, and the default value is 200KB,
which is not enough for run raw u-boot.bin.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We need to update TEXT BASE for TPL/SPL/U-Boot;
SPL no need relocate STACK after enable TPL, so remove it;
Don't enable pinctrl names so that SPL can get pinctrl dts;
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
rockchip pinctrl driver has update to use dts, so we need
to add the pinctrl config in SPL for sdmmc.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Migrate all the "u-boot,dm-pre-reloc" tag from rk3288-tinker.dts
into rk3288-tinker-u-boot.dtsi.
When both board level and soc level '-u-boot.dtsi' files exist,
we need to include the soc level 'rk3288-u-boot.dtsi' manually.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
More boards other than vyasa needs TPL, so enable the TPL configs
at chip level instead of board level.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The pointer to struct atf_image_info in
bl31_params_mem.bl31_params.bl31_image_info is not initialized before
being dereferenced. This can cause U-Boot to crash right before jumping
to the BL31 ATF binary.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Fixes: bcc1726a7b ("spl: add support to booting with ATF")
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There is a regression seen on Poplar platform, which doesn't even show
a U-Boot version banner on booting. It turns out that due to landing
of commit 3a7c45f6a7 ("simple-bus: add DM_FLAG_PRE_RELOC flag to
simple-bus driver"), we need to increase SYS_MALLOC_F_LEN from its
default size 0x400, as pre-relocation requires more memory there. Let's
increase SYS_MALLOC_F_LEN to 0x4000 to fix the regression.
Thanks to Andreas Färber <afaerber@suse.de> for reporting, and Bin Meng
<bmeng.cn@gmail.com> for trouble shooting.
Reported-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Move the sg_set_pinsel macro to arch/arm/mach-uniphier/arm32/debug_ll.S
since it is not used anywhere else.
Move the C functions sg_set_{pinsel,iectrl} to debug-uart.c since they
are not used anywhere else.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
debug_uart_init() is called from spl_board_init(), which is only
compiled for SPL. For U-boot proper, _debug_uart_init() is unreachable,
so dropped by the dead code elimination.
Now that 64-bit SoCs of this SoC family no longer support SPL,
debug-uart-ld20.c is never compiled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
