eaw/u-boot
1
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity
78,114 Commits 9 Branches 435 Tags
e5d8d08981aff1d191f46b3f4432b9f356c80256
Commit Graph

78114 Commits

This Branch
This Branch
All Branches
Author SHA1 Message Date
Michal Simek
e5d8d08981 arm64: zynqmp: Fix i2c addresses for zynqmp-p-a2197 
After double checking some i2c addresses are not correct. It is visible
from i2c dump

ZynqMP> i2c bus
Bus 3:	i2c@ff020000
   74: i2c-mux@74, offset len 1, flags 0
Bus 5:	i2c@ff020000->i2c-mux@74->i2c@0
Bus 6:	i2c@ff020000->i2c-mux@74->i2c@2
Bus 7:	i2c@ff020000->i2c-mux@74->i2c@1
Bus 8:	i2c@ff020000->i2c-mux@74->i2c@3
Bus 4:	i2c@ff030000  (active 4)
   74: i2c-mux@74, offset len 1, flags 0
Bus 9:	i2c@ff030000->i2c-mux@74->i2c@0
Bus 10:	i2c@ff030000->i2c-mux@74->i2c@3
Bus 11:	i2c@ff030000->i2c-mux@74->i2c@4
Bus 12:	i2c@ff030000->i2c-mux@74->i2c@5  (active 12)
   51: generic_51, offset len 1, flags 0
   60: generic_60, offset len 1, flags 0
   74: generic_74, offset len 1, flags 0
Bus 13:	i2c@ff030000->i2c-mux@74->i2c@6  (active 13)
   51: generic_51, offset len 1, flags 0
   5d: generic_5d, offset len 1, flags 0
   74: generic_74, offset len 1, flags 0
ZynqMP> i2c dev 4
Setting bus to 4
ZynqMP> i2c mw 74 0 18
ZynqMP> i2c probe
Valid chip addresses: 18 36 37 50 51 60 74
ZynqMP> i2c mw 74 0 20
ZynqMP> i2c probe
Valid chip addresses: 51 60 74

where it is clear that si570 (u5) is at 0x60 address and 8t49n240 (u39) is
also at address 0x60 based on log above.
i2c address 0x74 is i2c mux and 0x51 is eeprom.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/0a198e9d993411e41473d130d5a5c20b6dc83458.1646639616.git.michal.simek@xilinx.com
 2022-03-14 15:24:04 +01:00
Ashok Reddy Soma
dbd673f14d pinctrl: zynqmp: Add pinctrl driver 
Add pinctrl driver for Xilinx ZynqMP SOC. This driver is compatible with
linux device tree parameters for configuring pinmux and pinconf.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/2d7eefa83c8c0129f7243a25de56a289e948f6c6.1645626183.git.michal.simek@xilinx.com
 2022-03-14 15:23:31 +01:00
Ashok Reddy Soma
e19b8dda92 pinctrl: Increase length of pinmux status buffer 
Xilinx ZynqMP SOC can set 6 parameters for its pins. pinmux status
command will print the status of these parameters for each pin. But
current print buffer length is only 40 characters long, increase it
to 80 to print all the parameters.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/3a6be84c8354f38754a9838670cc0319e84f29e8.1645626183.git.michal.simek@xilinx.com
 2022-03-14 15:23:26 +01:00
Michal Simek
57d820da97 cmd: test: pinmux: Do not check all empty spaces 
There is really no value to check empty spaces. That's why use
ut_assert_nextlinen() instead of ut_assert_nextline().
This change ensures that PINMUX_SIZE can be increased without changing
tests.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/03aecf4c67ec8d72bf2a90baf1516fc5bd300fe0.1646668094.git.michal.simek@xilinx.com
 2022-03-14 15:22:57 +01:00
Michal Simek
a744a284e3 net: phy: Add support for ethernet-phy-id with gpio reset 
Ethernet phy like dp83867 is using strapping resistors to setup PHY
address. On Xilinx boards strapping is setup on wires which are connected
to SOC where internal pull ups/downs influnce phy address. That's why there
is a need to setup pins properly (via pinctrl driver for example) and then
perform phy reset. I can be workarounded by reset gpio done for mdio bus
but this is not working properly when multiply phys sitting on the same
bus. That's why it needs to be done via ethernet-phy-id driver where dt
binding has gpio reset per phy.

DT binding is available here:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-phy.yaml

The driver is are reading the vendor and device id from valid phy node
using ofnode_read_eth_phy_id() and creating a phy device.
Kconfig PHY_ETHERNET_ID symbol is used because not every platform has gpio
support.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Link: https://lore.kernel.org/r/70ab7d71c812b2c972d48c129e416c921af0d7f5.1645627539.git.michal.simek@xilinx.com
 2022-03-09 12:43:16 +01:00
Michal Simek
3249116d83 net: phy: Remove static return type for phy_device_create() 
Remove static return type for phy_device_create() to avoid file scope for
this function. Also add required prototype in phy.h.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Link: https://lore.kernel.org/r/1517f4053403fbd53e899d500e7485d068a4f0b6.1645627539.git.michal.simek@xilinx.com
 2022-03-09 12:43:16 +01:00
Michal Simek
db681d4929 net: phy: Add new read ethernet phy id function 
Add new function to get ethernet phy id from compatible property
of the mdio phy node.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Link: https://lore.kernel.org/r/16019efb3820a50330935fdaae191cec1f101b5c.1645627539.git.michal.simek@xilinx.com
 2022-03-09 12:43:16 +01:00
Michal Simek
d24b3e32ab MAINTAINERS: Remove duplicated entry for ehci-zynq.c 
ehci-zynq.c is assigned to Zynq and ZynqMP that's why remove one.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/d97779178fa56f1c6af40f5604b0bf349002cd36.1646639027.git.michal.simek@xilinx.com
 2022-03-09 12:42:31 +01:00
Neal Frager
9fb9ec5e24 arm64: zynqmp: add support for zcu106 rev1.0 
This patch adds psu_init for Xilinx ZCU106 rev1.0. Xilinx ZCU106 rev1.0 has
newer x16 DDR4 memories and it is SW compatible with revA.

Signed-off-by: Neal Frager <neal.frager@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/997b3e23457e4d24ce0e197d742382aaec36c2b2.1646230318.git.michal.simek@xilinx.com
 2022-03-09 12:39:33 +01:00
Sai Pavan Boddu
f76f86029d i2c: i2c-cdns: Prevent early termination of write 
During sequential loading of data, hold the bus to prevent controller
from sending stop signal in case no data is available in fifo.

Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/2407b39d305999cb42438c5423aebc3b514acabb.1646122610.git.michal.simek@xilinx.com
 2022-03-09 12:36:37 +01:00
Sai Pavan Boddu
94b3f3fc7d i2c: i2c-cdns: Fix write transaction state 
Start write transfer after loading data to FIFO.

Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/f0b3e443daa7758e00dfdcc245cf6b2120b0e907.1646122610.git.michal.simek@xilinx.com
 2022-03-09 12:36:37 +01:00
Sai Pavan Boddu
1bc2a79a4c i2c: i2c-cdns: Start read transaction after write to transfer_size reg 
Avoid a race condition where read transaction is started
keeping expected bytes as 0. Which sometimes would result in sending
STOP signal as no data is expected. Observed on QEMU platform.

Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Reviewed-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/487c8026791bfd60719403a2df2c54bb0ae99232.1646122610.git.michal.simek@xilinx.com
 2022-03-09 12:36:37 +01:00
Michal Simek
d926695cc5 dma: xilinx: Add Display Port DMA driver 
Display Port (DP) has own dma driver that's why add this skeleton driver
only for handling power domain setting and send configuration object to
PMUFW to enable it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/fe8bc313bcd430b04e9fa6fb770d5799ef28b350.1645627920.git.michal.simek@xilinx.com
 2022-03-09 12:35:50 +01:00
Michal Simek
98cacab765 video: Add skeleton driver for ZynqMP Display port driver 
The reason for this driver is to use call power management driver to enable
it in PMUFW. There is missing functionality now but should be added in
near future.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/598cb9515bbabc803f72e287464e3d107cd106a3.1645627920.git.michal.simek@xilinx.com
 2022-03-09 12:35:49 +01:00
Ashok Reddy Soma
90ab7fafb6 mmc: zynq_sdhci: Add support for dynamic configuration 
Add support for dynamic configuration which will takes care of
configuring the SD secure space configuration registers using firmware
APIs, performing SD reset assert and deassert.

High level sequence:
  - Check for the PM dynamic configuration support, if no error proceed
    with SD dynamic configurations(next steps) otherwise skip the dynamic
    configuration.
  - Put the SD Controller in reset.
  - Configure SD Fixed configurations.
  - Configure the SD Slot Type.
  - Configure the BASE_CLOCK.
  - Configure the 8-bit support.
  - Bring the SD Controller out of reset.

In the above steps, apart from the Fixed configurations, remaining all
configurations are dynamic and they will be read from devicetree.

And also remove hardcoded secure register writes, as dynamic sd config
support is added.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/030a3ec041ff3efebd574b4d2b477ad85f12cbce.1645626962.git.michal.simek@xilinx.com
 2022-03-09 12:34:47 +01:00
Ashok Reddy Soma
3adc17f60b lib: div64: Add support for round up of div64_u64 
Most of the frequencies are not rounded up to a proper number.
When we need to devide these frequencies to get a number for example
frequency in Mhz, we see it as one less than the actual intended value.
Ex: If we want to get Mhz from frequency 199999994hz, we will calculate
it using div64_u64(199999994, 1000000) and we will get 199Mhz in place
of 200Mhz.

Add a macro DIV64_U64_ROUND_UP for rounding up div64_u64. This is taken
from linux 'commit 68600f623d69("mm: don't miss the last page because of
round-off error")'.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/f9fdcba76cd692ae436b1d7883b490e3dc207231.1645626962.git.michal.simek@xilinx.com
 2022-03-09 12:34:47 +01:00
Ashok Reddy Soma
7d9ee46672 firmware: zynqmp: Add support for set sd config and is function supported 
Add firmware API's to set SD configuration and to check if a purticular
function is supported.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/f64fa2f73e4775e9ad2f4d91339d6c74b43116a3.1645626962.git.michal.simek@xilinx.com
 2022-03-09 12:34:47 +01:00
Ashok Reddy Soma
de5358a82c firmware: zynqmp: Add and update firmware enums 
Update enum pm_ioctl_id with more IOCTLs.
Add enum pm_sd_config_type to support dynamic sd configuration.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/9aba090ec11d2591dbe6978e73e64384873c99fc.1645626962.git.michal.simek@xilinx.com
 2022-03-09 12:34:47 +01:00
Michal Simek
2f6e1dde38 arm64: zynqmp: Fix level of gpio reset for usb on kv260 boards 
Active level is low that's why it should be fixed.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/86b3a96ce990b0ee0adab221146b5a5c751bd4a9.1645629459.git.michal.simek@xilinx.com
 2022-03-07 16:33:47 +01:00
Michal Simek
8b82a3a7fe arm64: zynqmp: Enable DP driver for SOMs 
The main reason is to send pmufw cfg overlay from U-Boot to PMUFW to enable
access to DP. Overlay is sent when cls command is called and for that IP
has to be enabled in carrier cards.
And IP needs to be also enabled in SOM dt because with DTB reselection new
DT is not parsed in pre reloc U-Boot instance. It is called from board_f
via embedded_dtb_select(). That's why bind function is not able to allocate
memory and it ends up with error:
"Video device 'display@fd4a0000' cannot allocate frame buffer memory
-ensure the device is set up before relocation"

To avoid this situation DP is placed also to SOM where bind function is
called and frame buffer memory is allocated and just reused after DTB
reselection. Result is the same. There could be a problem in Linux with
different DP configurations but that's need to be solved there because
console should be on from u-boot already.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/c4f31641f917fddb09d976f56875057c658f264c.1645629459.git.michal.simek@xilinx.com
 2022-03-07 16:33:47 +01:00
Michal Simek
ff79448294 arm64: zynqmp: Switch to ethernet-phy-id in kv260 
Use ethernet-phy-id compatible string to properly describe phy reset on
kv260 boards. Previous description wasn't correct because reset was done
for mdio bus to operate and it was in this case used for different purpose
which was eth phy reset. With ethernet-phy-id phy reset happens only for
the phy via phy framework.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/73b64f1a2b873b4e26bd2b365364bdf313794ae2.1645629459.git.michal.simek@xilinx.com
 2022-03-07 16:33:47 +01:00
Michal Simek
a3efa53c01 arm64: zynqmp: Use assigned-clock-rates for setting up clock in SOM 
With limited low level configuration done via psu-init only IPs connected
on SOM are initialized and configured. All IPs connected to carrier card
are not initialized. There is a need to do proper reset, pin configuration
and also clock setting.
The patch targets the last part which is setting up proper clock for USBs
and SDs.
Also setup proper bus width for SD cards.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri@xilinx.com>
Link: https://lore.kernel.org/r/d9f80b2551bd246c3d7ecb09b516806c8dc83ed9.1645629459.git.michal.simek@xilinx.com
 2022-03-07 16:33:47 +01:00
Michal Simek
59e1bdd48d arm64: zynqmp: Setup clock for DP and DPDMA 
Clocks are coming from shared HW design where these frequencies should be
aligned with PLL setup.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/04454c50d0d13e450976942085d763ab5aa38f98.1645629459.git.michal.simek@xilinx.com
 2022-03-07 16:33:47 +01:00
Michal Simek
c36dc2449b arm64: zynqmp: Move usb hub from i2c to usb node 
Based on upstream discussion based on link below usb hub should be placed
to usb node directly as child node. Based on this Linux driver was updated
and the same change should be also reflected in kv260 board.

Link: https://lore.kernel.org/all/CAL_JsqJZBbu+UXqUNdZwg-uv0PAsNg55026PTwhKr5wQtxCjVQ@mail.gmail.com/
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/aa18df1978f161b933e6cdc6cd99c807b5f74398.1645629459.git.michal.simek@xilinx.com
 2022-03-07 16:33:47 +01:00
Michal Simek
d7b5cc89d3 microblaze: Do not place u-boot to reserved memory location 
Microblaze can also have reserved space in DT which u-boot has to avoid to
placing self to that location. The same change was done in Zynqmp by commit
ce39ee28ec ("zynqmp: Do not place u-boot to reserved memory location").

This feature was tested with this memory description on kc705:

	memory {
		device_type = "memory";
		reg = <0x80000000 0x40000000>;
	};

	reserved-memory {
		#address-cells = <1>;
		#size-cells = <1>;
		ranges;

		alloc@b00000000 {
			reg = <0xb0000000 0x10000000>;
			no-map;
		};

		alloc@a8000000 {
			reg = <0xa8000000 0x00010000>;
			no-map;
		};
	};

And in U-Boot log you can check u-boot relocation address and reserved
locations.
U-Boot 2022.01-03974-gb1b4c2dea9b9 (Feb 25 2022 - 11:59:48 +0100)

Model: Xilinx MicroBlaze
DRAM:  1 GiB
Flash: 128 MiB
Loading Environment from nowhere... OK
In:    serial
Out:   serial
Err:   serial
Model: Xilinx MicroBlaze
Net:   AXI EMAC: 40c00000, phyaddr 7, interface gmii
eth0: ethernet@40c00000
U-BOOT for microblaze-generic

U-Boot-mONStR> bdi
...
DRAM bank   = 0x00000000
-> start    = 0x80000000
-> size     = 0x40000000
...
relocaddr   = 0xaff69000
...
lmb_dump_all:
 memory.cnt  = 0x1
 memory[0]	[0x80000000-0xbfffffff], 0x40000000 bytes flags: 0
 reserved.cnt  = 0x3
 reserved[0]	[0xa8000000-0xa800ffff], 0x00010000 bytes flags: 4
 reserved[1]	[0xafe87bb0-0xafffffff], 0x00178450 bytes flags: 0
 reserved[2]	[0xb0000000-0xbfffffff], 0x10000000 bytes flags: 4

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/ea0a8ccce723478eb518f6fdceb91d4f129efb68.1646122398.git.michal.simek@xilinx.com
 2022-03-07 16:33:47 +01:00
Michal Simek
fda7cbfefd power: zynqmp: Use zynqmp_pmufw_node() from firmware 
Remove private xpm_configobject[] and use zynqmp_pmufw_node() which
provides the same functionality.
Also add debug messages for easier debugging.

Fixes: e0283cbdfd ("power: zynqmp: Add power domain driver for ZynqMP")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Link: https://lore.kernel.org/r/bddf11459b9b9e849fac9a50db2f1a5fdfae4119.1646122254.git.michal.simek@xilinx.com
 2022-03-07 16:33:47 +01:00
T Karthik Reddy
15efe0f3a5 gpio: slg7xl45106: Add support for slg7xl45106 i2c gpo expander 
slg7xl45106 is i2c based 8-bit gpo expander, gpo pins are set and get by
writing and reading corresponding gpo bit value into its data register.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/839f475cc75c97ffb3496a4caa93de2faabdbca2.1645629688.git.michal.simek@xilinx.com
 2022-03-07 16:33:47 +01:00
Ashok Reddy Soma
980e55518f mmc: zynq_sdhci: Enable card detect workaround for ZynqMP 
Card detect state stable issue is observed on few ZynqMP boards(SOM),
so enable the workaround 'commit b6f44082d5 ("mmc: zynq_sdhci: Wait
till sd card detect state is stable")' for ZynqMP platforms also.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/0bf6154c79f24227d786efc5e2c1f506185b2bce.1645625609.git.michal.simek@xilinx.com
 2022-03-07 08:55:14 +01:00
Ashok Reddy Soma
8d32bca205 mmc: zynq_sdhci: Change granularity of timeout to 1us 
The timeout used in 'commit b6f44082d5 ("mmc: zynq_sdhci: Wait
till sd card detect state is stable")' workaround is 1000ms at a
granularity of 1msec. Change it to 1usec, to not waste time incase the
cd is stable.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/f008d2bcf864702a01564789f14f9cdecb8acd45.1645625609.git.michal.simek@xilinx.com
 2022-03-07 08:55:14 +01:00
Ashok Reddy Soma
c252b27747 mmc: zynq_sdhci: Fix timeout issue 
In the workaround added with 'commit b6f44082d5 ("mmc: zynq_sdhci: Wait
till sd card detect state is stable")' the timeout variable has post
decrement. Whenever timeout happens, this post decrement is making
timeout=0xffffffff, so timeout error print and return statement are
never reached. Fix it by decrementing it inside the while loop.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/61fc1160ada0dd622cd29e381a74af7bf3d9a200.1645625609.git.michal.simek@xilinx.com
 2022-03-07 08:55:14 +01:00
Michael Walle
03a8e826e0 ARM: dts: zynq: add NAND flash controller node 
Recently, a driver for the ARM Primecell PL35x static memory controller
(including NAND controller) was added in linux. Add the corresponding
device tree node.

Also update cfi-flash registers and location in DT.

Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/20210616155437.27378-3-michael@walle.cc
Link: https://lore.kernel.org/r/ee81d3846a1ce93f240d61537d404796e5599c1c.1645625433.git.michal.simek@xilinx.com
 2022-03-07 08:52:20 +01:00
Michal Simek
c2b74edf15 mtd: nand: Update driver to match new DT binding 
New binding changed node name from flash@e1000000 to nand-controller@0,0
which should be reflected in the driver. Both names are supported for
backward compatibility.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/61f6edd965e0c0b179184823d5283c6c61a1eb35.1645625433.git.michal.simek@xilinx.com
 2022-03-07 08:52:20 +01:00
Ashok Reddy Soma
4173a42685 dm: pinctrl: Use explicit values for enums 
Based on discussion at
https://lore.kernel.org/r/20200318125003.GA2727094@kroah.com we got
recommendation to use explicit values for all enums.

So, add explicit values to all pinctrl related enums for readability.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/dcdb20e7252ea7465e9f984d815e9624c30e9558.1645624969.git.michal.simek@xilinx.com
 2022-03-07 08:49:42 +01:00
T Karthik Reddy
2569b51e32 Revert "board: zynqmp: Fix for wrong AMS setting by ROM" 
This reverts commit dfbe492ede.
Analog bus control register should be programmed in SPL only. This commit
3414712ba8 ("arm64: zynqmp: Writing correct value to ANALOG_BUS") is
programming the same. So revert this commit.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/215bc936e36f88d2e7c4422ec68cad6d40cb8f68.1645624892.git.michal.simek@xilinx.com
 2022-03-07 08:49:08 +01:00
Ashok Reddy Soma
7a036b674f fru: ops: Add support to read mac addresses from multirecord 
Add support to read MAC addresses from mac address multirecord.
Check if multi record is found, then jump to mac address multirecord by
comparing the record type field. If it matches mac address
multirecord(0xD2), then copy mac addresses.

Copy these read MAC address in xilinx_read_eeprom_fru so that they are
updated to eth*addr in board_late_init_xilinx().

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/18f31bc528820934854ea5fd9dc581778fc1e40c.1645624855.git.michal.simek@xilinx.com
 2022-03-07 08:48:22 +01:00
Ashok Reddy Soma
ff8ee707fb xilinx: common: Optimise updating ethaddr from eeprom 
In board_late_init_xilinx() eth*addr are updated from the values read from
eeprom. Ideally the MAC addresses are updated sequencially. So if any
MAC address is invalid, it means there are no further valid values.
So optimise this logic by replacing continue with break.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/efef0d07add5d5777396ea111ad75411dc402db3.1645624855.git.michal.simek@xilinx.com
 2022-03-07 08:48:21 +01:00
Ashok Reddy Soma
90e8f2db60 fru: ops: Return error from checksum if data is all zero's 
fru_checksum function is simply adding all the bytes and returning the
sum. If the data passed to this function is all zero's then it will
return 0, and the functions calling this api will assume that checksum
is correct. Ideally this is not good. Fix this by returning error if all
the data is 0's.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/ac0366fe55c60a818a3f9ed33d96826c817d5520.1645624855.git.michal.simek@xilinx.com
 2022-03-07 08:48:21 +01:00
Ashok Reddy Soma
952b2e60de fru: ops: Clear fru table before storing data 
Fill fru table with 0's before using it, to avoid junk data.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/e5f15caf9c2102316e39f300d7c9c1ecb6be8439.1645624855.git.michal.simek@xilinx.com
 2022-03-07 08:48:21 +01:00
Tom Rini
6d3c46ed0e Merge https://source.denx.de/u-boot/custodians/u-boot-sunxi 
- Fix ARMv5/F1C100 FEL booting
- Fix F1C100 reset
- Introduce proper F1C100 boot method detection
- Enable SPI booting for F1C100

Boot tested from FEL, SPI, SD card and eMMC (where applicable) on
Pine64-LTS, Pine-H64, BananaPi M1, OrangePi Zero, LicheePi Nano(F1C100).
 2022-03-05 20:46:55 -05:00
Tom Rini
0444cbbe77 Merge branch '2022-03-04-assorted-minor-fixes' 
- mailmap file updates, OpenSSL code cleanup, assorted TI platform
  fixes, typo fix.
 2022-03-05 11:34:31 -05:00
Yann Droneaud
9b5ad4f5da lib: rsa: use actual OpenSSL 1.1.0 EVP MD API 
Since OpenSSL 1.1.0, EVP_MD_CTX_create() is EVP_MD_CTX_new()
                     EVP_MD_CTX_destroy() is EVP_MD_CTX_free()
                     EVP_MD_CTX_init() is EVP_MD_CTX_reset()

As there's no need to reset a newly created EVP_MD_CTX, moreover
EVP_DigestSignInit() does the reset, thus call to EVP_MD_CTX_init()
can be dropped.
As there's no need to reset an EVP_MD_CTX before it's destroyed,
as it will be reset by EVP_MD_CTX_free(), call to EVP_MD_CTX_reset()
is not needed and can be dropped.

Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
 2022-03-04 15:20:07 -05:00
Michal Simek
4fa4227cdd .mailmap: Record all address for main U-Boot contributor 
Based on looking at top contributors it was seen that top statistics from
top contributors don't include all contributions from different email
addresses. That's why I checked all top contributors are checked it.

git shortlog -n $START..$END -e -s

The patch is adding mapping for Bin Meng, Marek Vasut, Masahiro Yamada,
Michal Simek, Tom Rini, Wolfgang Denk.
And also use mapping for Stefan Roese and Wolfgang Denk to be properly
counted.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
 2022-03-04 15:20:06 -05:00
Heinrich Schuchardt
5017f9b595 mkimage: error handling for FIT image 
If parameter -F is given but FIT support is missing, a NULL pointer might
dereferenced (Coverity CID 350249).

If incorrect parameters are given, provide a message and show usage.

Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
 2022-03-04 15:20:06 -05:00
Sébastien Szymanski
55fd1c442e cmd: pwm: fix typo 'eisable' -> 'disable' 
Fixed misspelled 'disable' in help text.

Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
 2022-03-04 15:20:06 -05:00
Jan Kiszka
39834ccdd4 arm: dts: iot2050: Add cfg register space for ringacc and udmap 
Recent unrelated fixes (9876ae7db6) revealed that we were missing bits
from 2af181b53e in the IOT2050 dt. Add them, but only for main U-Boot.
SPL loads from QSPI only, thus cannot use DMA.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
 2022-03-04 15:20:06 -05:00
Aswath Govindraju
4403e1a31c configs: j721e_*_evm_a72_defconfig: Enable config for setting mmc speed mode 
Enable config for setting mmc speed mode from U-Boot command line.

Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
 2022-03-04 15:20:06 -05:00
Christian Gmeiner
f7fbe547d9 arm: mach-k3: am6_init: Use CONFIG_TI_I2C_BOARD_DETECT 
We only want to call do_board_detect() if CONFIG_TI_I2C_BOARD_DETECT
is set. Same as done for am64.

This makes it possible to add a custom am65 based board design to
U-Boot that does not use this board detection mechanism.

Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
 2022-03-04 15:20:06 -05:00
Romain Naour
4ff9a8c33c configs: ti: use standard configuration nodes naming 
Currently, any u-boot bootloader for ti armv7 platforms using
DEFAULT_FIT_TI_ARGS to boot with a fitimage (boot_fit = 1)
doesn't boot when built with Yocto Poky (openembedded-core).

  ## Loading kernel from FIT Image at 90000000 ...
  Could not find configuration node
  ERROR: can't get kernel image!

Arago forked the kernel-fitimage class [1] and altered the
configuration nodes naming while adding the OPTEE support by
using FITIMAGE_CONF_BY_NAME by default [2].

The "upstream" kernel-fitimage class from openembedded-core still
add the "conf-" prefix for each configuration nodes [3].

The ITS file format (from doc/uImage.FIT/source_file_format.txt)
is not really accurate with the expected naming of these nodes.
But in practice the "conf-" prefix is widely used.

When the FIT image support has been added for ti armv7 platforms
the naming from Arago has been used [3]. Fix this issue by adding
the prefix expected by the ITS file generated by kernel-fitimage
class from openembedded-core.

[1] http://arago-project.org/git/meta-arago.git?p=meta-arago.git;a=commitdiff;h=719ab1b2098bcdc59c249e3529fa82cb1b9130e6
[2] http://arago-project.org/git/meta-arago.git?p=meta-arago.git;a=commitdiff;h=f23f2876a0cda89241d031bb7ba0b4256ed90035
[3] https://git.openembedded.org/openembedded-core/tree/meta/classes/kernel-fitimage.bbclass?h=yocto-3.1.13#n290
[3] 1e93cc8473

Signed-off-by: Romain Naour <romain.naour@smile.fr>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Denys Dmytriyenko <denys@konsulko.com>
 2022-03-04 15:20:06 -05:00
Tom Rini
55b5c426ae Merge https://source.denx.de/u-boot/custodians/u-boot-marvell 
- pci_mvebu: Minor cleanup (Pali)
- mvebu: turris_omnia: Enable ext4 write support (Marek)
- a37xx: Misc fixes in PCI and pinctrl (Pali & Marek)
- a38x/rtc: Fix null pointer access (Francios)
- mvebu: x530: clearfog: Fix ODT configuration (Chris)
- kwboot: Fix boot and terminal mode (Pali)
 2022-03-04 08:27:32 -05:00
Pali Rohár
f4fa962fcd tools: kwboot: Update references with public links 
Public documents about BootROM of some Marvell SoCs are available in the
public Web Archive. Put this information into source code.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
 2022-03-04 13:12:43 +01:00