commit ce62bef8fac559e27245259882e45f19cdc293ad upstream.
- fix JIRA A7K8K-5056
- remove TEST_PATTERN write at the load patern stage earlier to WL SUP stage
- the WL SUP stage already writes this pattern to the memory, if the pattern exist at the memory
then the algorithm will fail, since it think that there are no phase to correct
Signed-off-by: Moti Buskila <motib@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Linux displays the real PCIe card connected to a mvebu PCIe slot as
device 0, not 1. This is done by setting local dev number to 1, so that
the local "Marvell Memory controller" device is on address 1.
Let's do it also in U-Boot.
With this commit the pci command in U-Boot prints something like:
=> pci
Scanning PCI devices on bus 0
BusDevFun VendorId DeviceId Device Class Sub-Class
_____________________________________________________________
00.00.00 0x168c 0x003c Network controller 0x80
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Refactor validation of bdf parameter in mvebu_pcie_read/write_config
functions.
We can simplify the code by putting the validation into separate
function.
Also there are always only two devices visible on local bus:
* on slot configured by function mvebu_pcie_set_local_dev_nr()
(by default this register is set to 0) there is a
"Marvell Memory controller", which isn't useful in root complex
mode,
* on all other slots the real PCIe card connected to the PCIe slot.
We can simplify the code even more by simply allowing access only to
the real PCIe card.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Other drivers (aardvark, intel_fpga) print "(addr,size,val)" when
debugging is enabled. Print size for pci_mvebu as well.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
PCI uclass maps PCI bus numbers to the seq member of struct udevice.
Use dev_seq(dev) as the bus number in mvebu_pcie_probe instead of an
incrementing a static variable.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Fix usage of VL805 XHCI PCIe controller when it is connected via PCIe to
Armada 3720 SOC. Without this U-Boot crashes when trying to access
enumerated USB devices connected to this XHCI PCIe controller.
This should be done according to the PCIe Link Initialization sequence, as
defined in Marvell Armada 3720 Functional Specification.
Linux has this code too.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
When copying to a u32 field we should use sizeof(u32) and not
sizeof(*u32) in memcpy.
On 64bit systems like cortina_presidio-asic-emmc_defconfig using
sizeof(*u32) leads to a buffer overrun.
Fixes: febe13b438 ("net: cortina_ni: Add eth support for Cortina Access CAxxxx SoCs")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
ca_do_bch_correction() takes a random value from the stack and starts
counting bitflips from this value. Initialize the counter.
This passed unnoticed as the value is finally ignored in the call
hierarchy.
Fixes: 161df94b3c ("mtd: rawnand: cortina_nand: Add Cortina CAxxxx SoC support")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The values of left_edge[0] and right_edge[0] are overwritten before they
are used. Remove the superfluous assignments.
Fixes: 285b3cb939 ("dm: ddr: socfpga: fix gen5 ddr driver to not use bss")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
In 8a8d24bd Simon dropped data from all the various _platdata calls
but it seems this wasn't caught for the RNG200 driver from when it
was posted to merged. This fixes that issue.
Fixes: 537f0018 (rng: Add iProc RNG200 driver)
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
VIRTIO_ID_MAX_NUM is the largest device ID plus 1. Therefore a device id
cannot be greater or equal to VIRTIO_ID_MAX_NUM. Fix the comparison
accordingly.
Fixes: 8fb49b4c7a ("dm: Add a new uclass driver for VirtIO transport devices")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Xilinx changes for v2021.04-rc3
qspi:
- Support for dual/quad mode
- Fix speed handling
clk:
- Add clock enable function for zynq/zynqmp/versal
gem:
- Enable clock for Versal
- Fix error path
- Fix mdio deregistration path
fpga:
- Fix buffer alignment for ZynqMP
xilinx:
- Fix reset reason clearing in ZynqMP
- Show silicon version in SPL for Zynq/ZynqMP
- Fix DTB selection for ZynqMP
- Rename zc1275 to zcu1275 to match DT name
If zynqmp_qspi_set_speed() is called multiple times with the same speed,
then on the second call it will skip recalculating the baud_rate_val as
it assumes the speed is already configured correctly. But it will still
write the baud_rate_val to the configuration register and call
zynqmp_gqspi_set_tapdelay(). Because it skipped recalculating the
baud_rate_val, it will use the initial value of 0 . This causes the
driver to run at maximum speed which for many spi flashes is too fast and
causes data corruption.
Instead only write out a new baud_rate_val if we have calculated the
correct baud_rate_val.
This opens up another issue with the "if (speed == 0)", we don't save
off the new plat->speed_hz value when setting the baud rate on the
speed=0 path. Instead mimic what the Linux zynqmp gqspi driver does, and
have speed==0 just use the same calculation as a normal speed. That will
cause the baud_rate_val to use the slowest speed possible, which is the
safest option.
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
CC: jagan@amarulasolutions.com
CC: michal.simek@xilinx.com
CC: Ashok Reddy Soma <ashokred@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable rx clock along with tx clock for versal platform. Use compatible
data to enable/disable clocks in the driver.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add clock enable functionality in versal clock driver to enable
clocks from peripheral drivers using clk_ops.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add clock enable functionality in zynqmp clock driver to enable
clocks from peripheral drivers using clk_ops.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
A lot of Xilinx drivers are checking -ENOSYS which means that clock driver
doesn't have enable function. Remove this checking from drivers and create
dummy enable function as was done for clk_fixed_rate driver by
commit 6bf6d81c11 ("clk: fixed_rate: add dummy enable() function").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Due to pointer arithmetic, "sizeof(u32) * ARCH_DMA_MINALIGN" is
subtracted. It seems that the original intention was to just subtract
ARCH_DMA_MINALIGN. Fix it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
- splash_source warning fix when building with 64-bit toolchains
- lq123p1jx31 and nv101wxmn51 compatible in simple panel driver
- remove not used mb862xx driver
- add Himax HX8238D panel driver
- s/video_uc_platdata/video_uc_plat/
The previous version printed the same debug message for both the enable
and disable routines without highlighting whether you were enabling or
disabling the module. It is now clear whether you are enabling or
disabling the module.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
i2c changes for v2021.04
new feature:
- Allow disabling driver model for I2C in SPL
fixes:
- i2c-gpio: Fix GPIO output
- at91: fix crash when using 'i2c probe'
Use CONFIG_IS_ENABLED() macro, which provides more convenient
way to check $(SPL)DM_I2C/$(SPL)DM_I2C_GPIO configs
for both SPL and U-Boot proper.
CONFIG_IS_ENABLED(DM_I2C) expands to:
- 1 if CONFIG_SPL_BUILD is undefined and CONFIG_DM_I2C is set to 'y',
- 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_DM_I2C is set to 'y',
- 0 otherwise.
All occurences were replaced automatically using these bash cmds:
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C/if !CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C/if CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C)/CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C_GPIO/if !CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C_GPIO/if CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C_GPIO)/CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
At present if U-Boot proper uses driver model for I2C, then SPL has to
also. While this is desirable, it places a significant barrier to moving
to driver model in some cases. For example, with a space-constrained SPL
it may be necessary to enable CONFIG_SPL_OF_PLATDATA which involves
adjusting some drivers.
This patch introduces a separate Kconfig symbols for enabling DM_I2C and
DM_I2C_GPIO support in SPL.
This will also help to get away from dirty workarounds to
achieve non-DM I2C support for SPL, which is currently used in some
board header files like:
ifdef CONFIG_SPL_BUILD
undef CONFIG_DM_I2C
endif
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
When issuing 'i2c probe', the driver was crashing, because at probe
there is a request with zero length buffer to write to i2c bus.
The xfer_msg function assumes the buffer is always there, and never
checks for the buffer length.
=> i2c dev 0
Setting bus to 0
=> i2c probe
Valid chip addresses:
data abort
pc : [<7ffa97dc>] lr : [<7ffa96f8>]
reloc pc : [<66f277dc>] lr : [<66f276f8>]
sp : 7fb7c110 ip : 7ff87a28 fp : 7ff99938
r10: 00000002 r9 : 7fb7dec0 r8 : 00000000
r7 : e181c600 r6 : 7fb88c20 r5 : 00000000 r4 : 7fb7c128
r3 : 00000000 r2 : 00000001 r1 : 00000000 r0 : 00000009
Flags: nZCv IRQs off FIQs off Mode SVC_32
Code: eb0092f4 e1a00005 e8bd81f0 e594300c (e5d33000)
Resetting CPU ...
Fixes: 8800e0fa20 ("i2c: atmel: add i2c driver")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
The dm_gpio_set_dir_flags function cannot be used to update the
configuration of a GPIO pin because it does a bitwise OR with the
existing flags. Looks like commit 788ea83412 ("gpio: add function
_dm_gpio_set_dir_flags") has introduced this behaviour and the i2c-gpio
driver has been broken since.
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
CC: Heiko Schocher <hs@denx.de>
CC: Patrick Delaunay <patrick.delaunay@st.com>
Because the first PCIExAR(n) register is configured with the mapping,
It is the second PCIExAR(n) register that must be written with 0, not
the last one. Update the n from 4 to 1 to select the correct register.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The mb862xx driver does not conform to the driver model and is unused.
Eliminate it.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add "boe,nv101wxmn51" to the compatible node. This is the panel for
chromebook_bob.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add "sharp,lq123p1jx31" to the compatible node. This is the panel for
chromebook_kevin.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
mmc_spi_sendcmd(), mmc_spi_readdata() and mmc_spi_writedata() are
currently undocumented. Add comment blocks to explain the arguments
and the return value.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
After command is sent and before card response shows up on the line,
there is a variable number of clock cycles in between called Ncr.
The spec [1] says the minimum is 1 byte and the maximum is 8 bytes.
Current logic in mmc_spi_sendcmd() has a flaw that it could only work
with certain SD cards with their Ncr being just 1 byte.
When resp_match is false, the codes try to receive only 1 byte from
the SD card. On the other hand when resp_match is true, the logic
happens to be no problem as it loops until timeout to receive as many
bytes as possible to see a match of the expected resp_match_value.
However not every call to mmc_spi_sendcmd() is made with resp_match
being true hence this exposes a potential issue with SD cards that
have a larger Ncr value.
Given no issue was reported as of today, we can reasonably conclude
that all cards being used on the supported boards happen to have a 1
byte Ncr timing requirement. But a broken case can be triggered by
utilizing QEMU to emulate a larger value of Ncr (by default 1 byte
Ncr is used on QEMU). This commit fixes such potential spec violation
to improve the card compatibility.
[1] "Physical Layer Specification Version 8.00"
chapter 7.5.1: Command / Response
chapter 7.5.4: Timing Values
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
After issuing the switch command: Wait until 'current state' of the card
status becomes 'tran'. This prevents from response timeout at the next
command because of 'current state' = 'data'.
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
If DMA(SDMA or ADMA) is not used, the cache invalidation
after reading is no need, should be skipped. Otherwise
U-Boot may hang at the cache invalidation.
Found this issue and tested this fix on DragonBoard 410c.
Fixes: commit 4155ad9aac ("mmc: sdhci: fix missing cache invalidation after reading by DMA")
Signed-off-by: Yuezhang.Mo <Yuezhang.Mo@sony.com>
Reviewed-by: Andy Wu <Andy.Wu@sony.com>
