2226ca1734
Now that proper load and execution addresses are set in v1 kwbimage we can use it for loading and booting U-Boot proper. Use the new spl_parse_board_header() function to implement parsing the kwbimage v1 header. Use information from this header to locate offset and size of the U-Boot proper binary, instead of using the legacy U-Boot header which is prepended to the U-Boot proper binary stored at fixed offset. This has the advantage that we do not need to relay on legacy U-Boot header anymore and therefore U-Boot proper binary can be stored at any offset, as is the case when loading & booting U-Boot proper by BootROM. The CONFIG_SYS_U_BOOT_OFFS option is therefore not used by SPL code anymore. Also allow to compile U-Boot SPL without CONFIG_SPL_SPI_FLASH_SUPPORT, CONFIG_SPL_MMC_SUPPORT or CONFIG_SPL_SATA_SUPPORT set. In this case BootROM is used for loading and executing U-Boot proper. This reduces the size of U-Boot's SPL image. By default these config options are enabled and so BootROM loading is not used. In some cases BootROM reads from SPI NOR at lower speed than U-Boot SPL. So people can decide whether they want to have smaller SPL binary at the cost of slower boot. Therefore dependency on CONFIG_SPL_DM_SPI, CONFIG_SPL_SPI_FLASH_SUPPORT, CONFIG_SPL_SPI_LOAD, CONFIG_SPL_SPI_SUPPORT, CONFIG_SPL_DM_GPIO, CONFIG_SPL_DM_MMC, CONFIG_SPL_GPIO_SUPPORT, CONFIG_SPL_LIBDISK_SUPPORT, CONFIG_SPL_MMC_SUPPORT, CONFIG_SPL_SATA_SUPPORT and CONFIG_SPL_LIBDISK_SUPPORT is changed from strict to related "imply" (which can be selectivelly turned off and causes booting via BootROM). Options CONFIG_SYS_SPI_U_BOOT_OFFS, CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR and CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_DATA_PART_OFFSET have to to be set to zero as they define the location where kwbimage header starts. It is the location where BootROM expects start of the kwbimage from which it reads, parses and executes SPL part. The same applies to option CONFIG_SPL_SATA_RAW_U_BOOT_SECTOR, which has to be set to one. Update all config files to set correct values of these options and set CONFIG_SYS_U_BOOT_OFFS to the correct value - the offset where U-Boot proper starts. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Reviewed-by: Stefan Roese <sr@denx.de>
144 lines
3.8 KiB
C
144 lines
3.8 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Copyright (C) 2017 Marek Behun <marek.behun@nic.cz>
|
|
* Copyright (C) 2016 Tomas Hlavacek <tomas.hlavacek@nic.cz>
|
|
*/
|
|
|
|
#ifndef _CONFIG_TURRIS_OMNIA_H
|
|
#define _CONFIG_TURRIS_OMNIA_H
|
|
|
|
/*
|
|
* High Level Configuration Options (easy to change)
|
|
*/
|
|
|
|
/*
|
|
* TEXT_BASE needs to be below 16MiB, since this area is scrubbed
|
|
* for DDR ECC byte filling in the SPL before loading the main
|
|
* U-Boot into it.
|
|
*/
|
|
#define CONFIG_SYS_TCLK 250000000 /* 250MHz */
|
|
|
|
/* USB/EHCI configuration */
|
|
#define CONFIG_EHCI_IS_TDI
|
|
|
|
/* Environment in SPI NOR flash */
|
|
|
|
#define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */
|
|
|
|
/* Keep device tree and initrd in lower memory so the kernel can access them */
|
|
#define RELOCATION_LIMITS_ENV_SETTINGS \
|
|
"fdt_high=0x10000000\0" \
|
|
"initrd_high=0x10000000\0"
|
|
|
|
/* Defines for SPL */
|
|
#define CONFIG_SPL_SIZE (140 << 10)
|
|
#define CONFIG_SPL_MAX_SIZE (CONFIG_SPL_SIZE - 0x0030)
|
|
|
|
#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + CONFIG_SPL_SIZE)
|
|
#define CONFIG_SPL_BSS_MAX_SIZE (16 << 10)
|
|
|
|
#ifdef CONFIG_SPL_BUILD
|
|
#define CONFIG_SYS_MALLOC_SIMPLE
|
|
#endif
|
|
|
|
#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10))
|
|
#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)
|
|
#define CONFIG_SPL_DRIVERS_MISC
|
|
|
|
#ifdef CONFIG_MVEBU_SPL_BOOT_DEVICE_SPI
|
|
/* SPL related SPI defines */
|
|
# define CONFIG_SYS_U_BOOT_OFFS 0x24000
|
|
#endif
|
|
|
|
#ifdef CONFIG_MVEBU_SPL_BOOT_DEVICE_MMC
|
|
/* SPL related MMC defines */
|
|
# define CONFIG_SYS_U_BOOT_OFFS (160 << 10)
|
|
# ifdef CONFIG_SPL_BUILD
|
|
# define CONFIG_FIXED_SDHCI_ALIGNED_BUFFER 0x00180000 /* in SDRAM */
|
|
# endif
|
|
#endif
|
|
|
|
/*
|
|
* mv-common.h should be defined after CMD configs since it used them
|
|
* to enable certain macros
|
|
*/
|
|
#include "mv-common.h"
|
|
|
|
/* Include the common distro boot environment */
|
|
#ifndef CONFIG_SPL_BUILD
|
|
|
|
#ifdef CONFIG_MMC
|
|
#define BOOT_TARGET_DEVICES_MMC(func) func(MMC, mmc, 0)
|
|
#else
|
|
#define BOOT_TARGET_DEVICES_MMC(func)
|
|
#endif
|
|
|
|
#ifdef CONFIG_USB_STORAGE
|
|
#define BOOT_TARGET_DEVICES_USB(func) func(USB, usb, 0)
|
|
#else
|
|
#define BOOT_TARGET_DEVICES_USB(func)
|
|
#endif
|
|
|
|
#ifdef CONFIG_SCSI
|
|
#define BOOT_TARGET_DEVICES_SCSI(func) func(SCSI, scsi, 0)
|
|
#else
|
|
#define BOOT_TARGET_DEVICES_SCSI(func)
|
|
#endif
|
|
|
|
#define BOOT_TARGET_DEVICES(func) \
|
|
BOOT_TARGET_DEVICES_MMC(func) \
|
|
BOOT_TARGET_DEVICES_SCSI(func) \
|
|
BOOT_TARGET_DEVICES_USB(func) \
|
|
func(PXE, pxe, na) \
|
|
func(DHCP, dhcp, na)
|
|
|
|
#define KERNEL_ADDR_R __stringify(0x1000000)
|
|
#define FDT_ADDR_R __stringify(0x2000000)
|
|
#define RAMDISK_ADDR_R __stringify(0x2200000)
|
|
#define SCRIPT_ADDR_R __stringify(0x1800000)
|
|
#define PXEFILE_ADDR_R __stringify(0x1900000)
|
|
|
|
#define LOAD_ADDRESS_ENV_SETTINGS \
|
|
"kernel_addr_r=" KERNEL_ADDR_R "\0" \
|
|
"fdt_addr_r=" FDT_ADDR_R "\0" \
|
|
"ramdisk_addr_r=" RAMDISK_ADDR_R "\0" \
|
|
"scriptaddr=" SCRIPT_ADDR_R "\0" \
|
|
"pxefile_addr_r=" PXEFILE_ADDR_R "\0"
|
|
|
|
#include <config_distro_bootcmd.h>
|
|
|
|
/*
|
|
* The factory reset bootcommand on Omnia first sets all the front LEDs to green
|
|
* and then tries to load the rescue image from SPI flash memory and boot it
|
|
*/
|
|
#define TURRIS_OMNIA_BOOTCMD_RESCUE \
|
|
"i2c dev 2; " \
|
|
"i2c mw 0x2a.1 0x3 0x1c 1; " \
|
|
"i2c mw 0x2a.1 0x4 0x1c 1; " \
|
|
"mw.l 0x01000000 0x00ff000c; " \
|
|
"i2c write 0x01000000 0x2a.1 0x5 4 -s; " \
|
|
"setenv bootargs \"earlyprintk console=ttyS0,115200" \
|
|
" omniarescue=$omnia_reset rescue_mode=$omnia_reset\"; " \
|
|
"sf probe; " \
|
|
"sf read 0x1000000 0x100000 0x700000; " \
|
|
"lzmadec 0x1000000 0x1700000; " \
|
|
"if gpio input gpio@71_4; then " \
|
|
"bootm 0x1700000#sfp; " \
|
|
"else " \
|
|
"bootm 0x1700000; " \
|
|
"fi; " \
|
|
"bootz 0x1000000"
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
RELOCATION_LIMITS_ENV_SETTINGS \
|
|
LOAD_ADDRESS_ENV_SETTINGS \
|
|
"fdtfile=" CONFIG_DEFAULT_DEVICE_TREE ".dtb\0" \
|
|
"console=ttyS0,115200\0" \
|
|
"ethact=ethernet@34000\0" \
|
|
"bootcmd_rescue=" TURRIS_OMNIA_BOOTCMD_RESCUE "\0" \
|
|
BOOTENV
|
|
|
|
#endif /* CONFIG_SPL_BUILD */
|
|
|
|
#endif /* _CONFIG_TURRIS_OMNIA_H */
|