Remove volatile keyword usage from arrays, they are not really volatile
in any way, so this keyword is misused here. No functional change.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Change type of private struct member mdio_base from void * to
phys_addr_t. This allows us to drop 2 casts.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
When gpio_request_by_name allocates a gpio output it by default will
de-assert the gpio which for phy-reset will take the PHY out of reset.
As this occurs before eth_phy_reset is called to assert the reset
line it can cause undesired affects if reset timings are not properly
met.
Configure the gpio with GPIOD_IS_OUT_ACTIVE so that reset is kept active
(reset asserted) to avoid this.
Cc: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
When gpio_request_by_name allocates a gpio output it by default will
de-assert the gpio which for phy-reset will take the PHY out of reset.
As this occurs before fec_gpio_reset is called to assert the reset
line it can cause undesired affects if reset timings are not properly
met.
Configure the gpio with GPIOD_IS_OUT_ACTIVE so that reset is kept active
(reset asserted) to avoid this.
Cc: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Adam Ford <aford173@gmail.com> #imx8mm-beacon
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Currently we require PHY interface mode to be known when
finding/creating the PHY - the functions
* phy_connect_phy_id()
* phy_device_create()
* create_phy_by_mask()
* search_for_existing_phy()
* get_phy_device_by_mask()
* phy_find_by_mask()
all require the interface parameter, but the only thing done with it is
that it is assigned to phydev->interface.
This makes it impossible to find a PHY device without overwriting the
set mode.
Since the interface mode is not used during .probe() and should be used
at first in .config(), drop the interface parameter from these
functions. Make the default value of phydev->interface (in
phy_device_create()) to be PHY_INTERFACE_MODE_NA. Move the interface
parameter to phy_connect_dev(), where it should be.
Change all occurrences treewide. In occurrences where we don't call
phy_connect_dev() for some reason (they only configure the PHY without
connecting it to an ethernet controller), set
phydev->interface = value from phy_find_by_mask call.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
The bcmgenet and sun8i_emac drivers call phy_connect(), which finds /
creates the PHY and also connects it to the eth device via
phy_connect_dev(), then set some phydev members (bcmgenet only), and
then call phy_connect_dev() explicitly again.
Drop the second phy_connect_dev(), since it is unnecesary.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Use phydev->is_c45 instead of is_10g_interface(phydev->interface) to
determine whether clause 45 protocol should be used.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
We want to be able to have phydev->interface uninitialized during
->probe(). We should assume that phydev->interface is initialized only
before ->config().
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Rename constant PHY_INTERFACE_MODE_NONE to PHY_INTERFACE_MODE_NA to make
it compatible with Linux' naming.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Rename constant PHY_INTERFACE_MODE_COUNT to PHY_INTERFACE_MODE_MAX to
make it compatible with Linux' naming.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Add helpers ofnode_read_phy_mode() and dev_read_phy_mode() to parse the
"phy-mode" / "phy-connection-type" property. Add corresponding UT test.
Use them treewide.
This allows us to inline the phy_get_interface_by_name() into
ofnode_read_phy_mode(), since the former is not used anymore.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Use the new dm_mdio_read/write/reset() wrappers treewide, instead of
always getting and dereferencing MDIO operations structure pointer.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
The type of the return value of phy_read() and phy_read_mmd() is int.
Change the variable to not be unsigned so that we not get into an
unsigned compared against 0.
Signed-off-by: Haolin Li <li.haolin@qq.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
A DM_ETH driver may use phy_connect() towards a PHY address on an MDIO
bus which is not specified in the device tree, as evidenced by:
pfe_eth_probe
-> pfe_phy_configure
-> phy_connect
When this happens, the PHY will have an invalid OF node.
When ar803x_config() runs, it silently fails at ar803x_of_init(), and
therefore, fails to run the rest of the initialization.
This makes MII_BMCR contain what it had after BMCR_RESET (0x8000) has
been written into it by phy_reset(). Since BMCR_RESET is volatile and
self-clearing, the MII_BMCR ends up having a value of 0x0. The further
configuration of this register, which is supposed to be handled by
genphy_config_aneg() lower in ar803x_config(), never gets a chance to
run due to this early error from ar803x_of_init().
As a result of having MII_BMCR as 0, the following symptom appears:
=> setenv ethact pfe_eth0
=> setenv ipaddr 10.0.0.1
=> ping 10.0.0.2
pfe_eth0 Waiting for PHY auto negotiation to complete......... TIMEOUT !
Could not initialize PHY pfe_eth0
Manually writing 0x1140 into register 0 of the PHY makes the connection
work, but it is rather desirable that the port works without any manual
intervention.
Fixes: fe6293a809 ("phy: atheros: add device tree bindings and config")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
A DM_ETH driver may use phy_connect() towards a PHY address on an MDIO
bus which is not specified in the device tree, as evidenced by:
pfe_eth_probe
-> pfe_phy_configure
-> phy_connect
When this happens, the PHY will have an invalid OF node.
The dp83867_config() method has extra initialization steps which are
bypassed when the PHY lacks an OF node, which is undesirable because it
will lead to broken networking. Allow the rest of the code to run.
Fixes: 085445ca41 ("net: phy: ti: Allow the driver to be more configurable")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
With all boards now using DM_ETH we determine the value for
CONFIG_FEC_XCV_TYPE at run time, except in the case of the default
fall-back. Set the fallback directly now.
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Ethernet phy like dp83867 is using strapping resistors to setup PHY
address. On Xilinx boards strapping is setup on wires which are connected
to SOC where internal pull ups/downs influnce phy address. That's why there
is a need to setup pins properly (via pinctrl driver for example) and then
perform phy reset. I can be workarounded by reset gpio done for mdio bus
but this is not working properly when multiply phys sitting on the same
bus. That's why it needs to be done via ethernet-phy-id driver where dt
binding has gpio reset per phy.
DT binding is available here:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-phy.yaml
The driver is are reading the vendor and device id from valid phy node
using ofnode_read_eth_phy_id() and creating a phy device.
Kconfig PHY_ETHERNET_ID symbol is used because not every platform has gpio
support.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Link: https://lore.kernel.org/r/70ab7d71c812b2c972d48c129e416c921af0d7f5.1645627539.git.michal.simek@xilinx.com
Some boards like the Beacon RZ/G2 SOM use either flags for
tx-internal-delay-ps, rx-internal-delay-ps or rgmii-rxid.
In Linux the APSR_RDM flag is set when either rx-internal-delay-ps
is set or the mode is rgmii-rxid, and the APSR_TDM is set when
tx-internal-delay-ps is found or rgmii-txid is set, and both
are set if rgmii-id is set.
The ravb driver in U-Boot driver was missing rgmii-rxid support,
so add that support in a similar fashion to what is done in Linux.
Signed-off-by: Adam Ford <aford173@gmail.com>
In case fastboot over Ethernet, am65_cpsw_stop() is not called unless
DM_FLAG_OS_PREPARE is set. Without call to am65_cpsw_stop(), DMA
resources are not released thus leading to failures in kernel.
Fix this by adding DM_FLAG_OS_PREPARE flag to am65_cpsw_nuss_port
driver.
Reported-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
If we just use fdtdec_get_addr_size_fixed to get "reg" it will use
64bit address cell to get the base address.
soc {
#address-cells = <1>;
#size-cells = <1>;
compatible ="SiFive,FU500-soc", "fu500-soc", "sifive-soc", "simple-bus";
ranges;
L28: axidma@30010000 {
#dma-cells = <1>;
compatible = "xlnx,axi-dma-1.00.a";
axistream-connected = <&L27>;
axistream-control-connected = <&L27>;
clocks = <&L1>;
interrupt-parent = <&L6>;
interrupts = <32 33>;
reg = <0x30010000 0x4000>;
fdtdec_get_addr_size_fixed: reg: addr=3001000000004000
We should get the base address through its parent's address-cells and
size-cells settings. So we should use fdtdec_get_addr_size_auto_parent()
to get correct base address.
After applying this patch, we can get the correct base address of dma by
replacing fdtdec_get_addr_size_fixed() with
fdtdec_get_addr_size_auto_parent().
fdtdec_get_addr_size_auto_parent:
na=1, ns=1, fdtdec_get_addr_size_fixed: reg: addr=30010000
Signed-off-by: Greentime Hu <greentime.hu@sifive.com>
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Link: https://lore.kernel.org/r/20220120084128.1892101-1-andy.chiu@sifive.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
- fdt_support: Add fdt_for_each_node_by_compatible() helper macro
(Marek)
- turris_omnia: Fixup SATA or PCIe nodes at runtime in DT blob (Pali)
- pci_mvebu: Add support for Kirkwood PCIe controllers (Pali)
- SPL: More verifications for kwbimage in SPL (Pali)
- mvebu: Remove comphy_update_map() (Pali)
- Minor misc stuff
Add macro fdt_for_each_node_by_compatible() to allow iterating over
fdt nodes by compatible string.
Convert various usages of
off = fdt_node_offset_by_compatible(fdt, start, compat);
while (off > 0) {
code();
off = fdt_node_offset_by_compatible(fdt, off, compat);
}
and similar, to
fdt_for_each_node_by_compatible(off, fdt, start, compat)
code();
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Xilinx changes for v2022.04-rc1
gpio:
- Add modepin driver
net:
- Save random mac addresses to eth variable
zynqmp gem:
- Add support for mdio bus DT description
- Add support for reset and SGMII phy configuration
- Reduce timeout for MDIO accesses
zynqmp clk:
- Fix clock handling for gem and usb
phy:
- Add zynqmp phy/serdes driver
serial:
- Add one missing compatible string
microblaze:
- Symbol alignement
- SPL fixups
- Code cleanups
zynqmp:
- Various dt changes, DP pre-reloc, gem resets, gem clocks
- Switch SOM to shared psu configuration
- Move dcache handling to firmware driver
- Workaround gmii2rgmii DT description issue
- Enable broadcasts again
- Change firmware enablement logic
- Small adjustement in firmware driver
versal:
- Support new mmc@ DT nodes
- Fix run time variable handling
- Add missing I2C_PMC ID for power domain
Add support of the MAC controller of Aspeed AST2600 SOC. The MAC
controller is the same with AST2500, except it has stand-alone MDIO
hardware block.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add support for DM_MDIO to connect to PHY. For the systems that have a
stand-alone MDIO hardware block, enable CONFIG_DM_MDIO to use driver
model for MDIO devices.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
- Let am335x_evm use the CPSW or PRUSS ethernet.
- Implement timer_get_boot_us in the omap timer driver
- gpmc bitflip, QSPI clock calculation on am437x, da8xx_gpio bugfixes
- Assorted K3 updates
For configurations with gmii2rgmii and external phy the DT nodes link
should be gem->gmii2rgmii->phy. But due to limitation in Linux driver
the DT is mentioned as gem->phy and gmii2rgmii->phy as shown in below DT.
ethernet@ff0c0000 {
compatible = "cdns,zynqmp-gem\0cdns,gem";
status = "okay";
interrupt-parent = <0x04>;
interrupts = <0x00 0x3b 0x04 0x00 0x3b 0x04>;
reg = <0x00 0xff0c0000 0x00 0x1000>;
clock-names = "pclk\0hclk\0tx_clk\0rx_clk\0tsu_clk";
#address-cells = <0x01>;
#size-cells = <0x00>;
#stream-id-cells = <0x01>;
iommus = <0x0d 0x875>;
power-domains = <0x0c 0x1e>;
clocks = <0x03 0x1f 0x03 0x69 0x03 0x2e 0x03 0x32 0x03 0x2c>;
phy-handle = <0x0e>;
phy-mode = "gmii";
xlnx,ptp-enet-clock = <0x00>;
local-mac-address = [ff ff ff ff ff ff];
phandle = <0x4d>;
mdio {
#address-cells = <0x01>;
#size-cells = <0x00>;
phandle = <0x4e>;
ethernet-phy@1 {
reg = <0x01>;
rxc-skew-ps = <0x708>;
txc-skew-ps = <0x708>;
phandle = <0x0e>;
};
gmii_to_rgmii_0@8 {
compatible = "xlnx,gmii-to-rgmii-1.0";
phy-handle = <0x0e>;
reg = <0x08>;
phandle = <0x4f>;
};
};
};
Since same DT is used in Linux and U-Boot we need to workaround this
issue by using the gmii2rgmii node which points to phy and we should
ignore the gem pointing to phy directly.
Do this workaround by updating priv->phydev->node value with
priv->phy_of_node only if it is not valid node.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Link: https://lore.kernel.org/r/641eb13425ffe80e0743f60cf90d0f940577b9e9.1642162085.git.michal.simek@xilinx.com
