Merge branch 'u-boot-microblaze/zynq' into 'u-boot-arm/master'

include/configs/zynq-common.h

@@ -83,10 +83,27 @@
 # define CONFIG_SDHCI
 # define CONFIG_ZYNQ_SDHCI
 # define CONFIG_CMD_MMC
-# define CONFIG_CMD_FAT
+#endif
+
+#ifdef CONFIG_ZYNQ_USB
+# define CONFIG_USB_EHCI
+# define CONFIG_CMD_USB
+# define CONFIG_USB_STORAGE
+# define CONFIG_USB_EHCI_ZYNQ
+# define CONFIG_USB_ULPI_VIEWPORT
+# define CONFIG_USB_ULPI
+# define CONFIG_EHCI_IS_TDI
+# define CONFIG_USB_MAX_CONTROLLER_COUNT	2
+#endif
+
+#if defined(CONFIG_ZYNQ_SDHCI) || defined(CONFIG_ZYNQ_USB)
 # define CONFIG_SUPPORT_VFAT
+# define CONFIG_CMD_FAT
 # define CONFIG_CMD_EXT2
+# define CONFIG_FAT_WRITE
 # define CONFIG_DOS_PARTITION
+# define CONFIG_CMD_EXT4
+# define CONFIG_CMD_EXT4_WRITE
 #endif
 
 #define CONFIG_SYS_I2C_ZYNQ
@@ -150,7 +167,13 @@
 		"bootm ${load_addr}\0" \
 	"jtagboot=echo TFTPing FIT to RAM... && " \
 		"tftpboot ${load_addr} ${fit_image} && " \
-		"bootm ${load_addr}\0"
+		"bootm ${load_addr}\0" \
+	"usbboot=if usb start; then " \
+			"echo Copying FIT from USB to RAM... && " \
+			"fatload usb 0 ${load_addr} ${fit_image} && " \
+			"bootm ${load_addr}\0" \
+		"fi\0"
+
 #define CONFIG_BOOTCOMMAND		"run $modeboot"
 #define CONFIG_BOOTDELAY		3 /* -1 to Disable autoboot */
 #define CONFIG_SYS_LOAD_ADDR		0 /* default? */
@@ -165,7 +188,7 @@
 #define CONFIG_SYS_LONGHELP
 #define CONFIG_CLOCKS
 #define CONFIG_CMD_CLK
-#define CONFIG_SYS_MAXARGS		15 /* max number of command args */
+#define CONFIG_SYS_MAXARGS		32 /* max number of command args */
 #define CONFIG_SYS_CBSIZE		256 /* Console I/O Buffer Size */
 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
 					sizeof(CONFIG_SYS_PROMPT) + 16)
@@ -213,7 +236,7 @@
 #define CONFIG_RSA
 
 /* Extend size of kernel image for uncompression */
-#define CONFIG_SYS_BOOTM_LEN	(20 * 1024 * 1024)
+#define CONFIG_SYS_BOOTM_LEN	(60 * 1024 * 1024)
 
 /* Boot FreeBSD/vxWorks from an ELF image */
 #if defined(CONFIG_ZYNQ_BOOT_FREEBSD)
@@ -239,16 +262,10 @@
 #define CONFIG_SPL_LIBCOMMON_SUPPORT
 #define CONFIG_SPL_LIBGENERIC_SUPPORT
 #define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_BOARD_INIT
 
 #define CONFIG_SPL_LDSCRIPT	"arch/arm/cpu/armv7/zynq/u-boot-spl.lds"
 
-/* Disable dcache for SPL just for sure */
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SYS_DCACHE_OFF
-#undef CONFIG_FPGA
-#undef CONFIG_OF_CONTROL
-#endif
-
 /* MMC support */
 #ifdef CONFIG_ZYNQ_SDHCI0
 #define CONFIG_SPL_MMC_SUPPORT
@@ -257,7 +274,18 @@
 #define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION    1
 #define CONFIG_SPL_LIBDISK_SUPPORT
 #define CONFIG_SPL_FAT_SUPPORT
-#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME     "u-boot.img"
+#if defined(CONFIG_OF_CONTROL) && defined(CONFIG_OF_SEPARATE)
+# define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME     "u-boot-dtb.img"
+#else
+# define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME     "u-boot.img"
+#endif
+#endif
+
+/* Disable dcache for SPL just for sure */
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_DCACHE_OFF
+#undef CONFIG_FPGA
+#undef CONFIG_OF_CONTROL
 #endif
 
 /* Address in RAM where the parameters must be copied by SPL. */

include/configs/zynq_zc70x.h

@@ -19,6 +19,7 @@
 #define CONFIG_SYS_NO_FLASH
 
 #define CONFIG_ZYNQ_SDHCI0
+#define CONFIG_ZYNQ_USB
 #define CONFIG_ZYNQ_I2C0
 #define CONFIG_ZYNQ_EEPROM
 #define CONFIG_ZYNQ_BOOT_FREEBSD

include/configs/zynq_zed.h

@@ -18,6 +18,7 @@
 
 #define CONFIG_SYS_NO_FLASH
 
+#define CONFIG_ZYNQ_USB
 #define CONFIG_ZYNQ_SDHCI0
 #define CONFIG_ZYNQ_BOOT_FREEBSD
 #define CONFIG_DEFAULT_DEVICE_TREE	zynq-zed