powerpc: Remove T1024QDS_DDR4_SECURE_BOOT_defconfig board
DM_SPI and other driver model migration deadlines are expired for this board. Remove it. Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This commit is contained in:
Jagan Teki
@@ -205,16 +205,6 @@ config TARGET_QEMU_PPCE500
|
||||
select ARCH_QEMU_E500
|
||||
select PHYS_64BIT
|
||||
|
||||
config TARGET_T1024QDS
|
||||
bool "Support T1024QDS"
|
||||
select ARCH_T1024
|
||||
select BOARD_LATE_INIT if CHAIN_OF_TRUST
|
||||
select SUPPORT_SPL
|
||||
select PHYS_64BIT
|
||||
imply CMD_EEPROM
|
||||
imply CMD_SATA
|
||||
imply FSL_SATA
|
||||
|
||||
config TARGET_T1023RDB
|
||||
bool "Support T1023RDB"
|
||||
select ARCH_T1023
|
||||
@@ -1554,7 +1544,6 @@ source "board/freescale/p1_p2_rdb_pc/Kconfig"
|
||||
source "board/freescale/p1_twr/Kconfig"
|
||||
source "board/freescale/p2041rdb/Kconfig"
|
||||
source "board/freescale/qemu-ppce500/Kconfig"
|
||||
source "board/freescale/t102xqds/Kconfig"
|
||||
source "board/freescale/t102xrdb/Kconfig"
|
||||
source "board/freescale/t1040qds/Kconfig"
|
||||
source "board/freescale/t104xrdb/Kconfig"
|
||||
|
||||
@@ -1,14 +0,0 @@
|
||||
if TARGET_T1024QDS
|
||||
|
||||
config SYS_BOARD
|
||||
default "t102xqds"
|
||||
|
||||
config SYS_VENDOR
|
||||
default "freescale"
|
||||
|
||||
config SYS_CONFIG_NAME
|
||||
default "T102xQDS"
|
||||
|
||||
source "board/freescale/common/Kconfig"
|
||||
|
||||
endif
|
||||
@@ -1,12 +0,0 @@
|
||||
T102XQDS BOARD
|
||||
#M: Shengzhou Liu <Shengzhou.Liu@freescale.com>
|
||||
S: Orphan (since 2018-05)
|
||||
F: board/freescale/t102xqds/
|
||||
F: include/configs/T102xQDS.h
|
||||
F: configs/T1024QDS_defconfig
|
||||
F: configs/T1024QDS_NAND_defconfig
|
||||
F: configs/T1024QDS_SDCARD_defconfig
|
||||
F: configs/T1024QDS_SPIFLASH_defconfig
|
||||
F: configs/T1024QDS_DDR4_defconfig
|
||||
F: configs/T1024QDS_SECURE_BOOT_defconfig
|
||||
F: configs/T1024QDS_DDR4_SECURE_BOOT_defconfig
|
||||
@@ -1,15 +0,0 @@
|
||||
# SPDX-License-Identifier: GPL-2.0+
|
||||
#
|
||||
# Copyright 2014 Freescale Semiconductor, Inc.
|
||||
|
||||
ifdef CONFIG_SPL_BUILD
|
||||
obj-y += spl.o
|
||||
else
|
||||
obj-y += t102xqds.o
|
||||
obj-y += eth_t102xqds.o
|
||||
obj-$(CONFIG_PCI) += pci.o
|
||||
obj-$(CONFIG_FSL_DIU_FB) += ../t1040qds/diu.o
|
||||
endif
|
||||
obj-y += ddr.o
|
||||
obj-y += law.o
|
||||
obj-y += tlb.o
|
||||
@@ -1,328 +0,0 @@
|
||||
T1024 SoC Overview
|
||||
------------------
|
||||
The T1024/T1023 dual core and T1014/T1013 single core QorIQ communication processor
|
||||
combines two or one 64-bit Power Architecture e5500 core respectively with high
|
||||
performance datapath acceleration logic, and network peripheral bus interfaces
|
||||
required for networking and telecommunications. This processor can be used in
|
||||
applications such as enterprise WLAN access points, routers, switches, firewall
|
||||
and other packet processing intensive small enterprise and branch office appliances,
|
||||
and general-purpose embedded computing. Its high level of integration offers
|
||||
significant performance benefits and greatly helps to simplify board design.
|
||||
|
||||
|
||||
The T1024 SoC includes the following function and features:
|
||||
- two e5500 cores, each with a private 256 KB L2 cache
|
||||
- Up to 1.4 GHz with 64-bit ISA support (Power Architecture v2.06-compliant)
|
||||
- Three levels of instructions: User, supervisor, and hypervisor
|
||||
- Independent boot and reset
|
||||
- Secure boot capability
|
||||
- 256 KB shared L3 CoreNet platform cache (CPC)
|
||||
- Interconnect CoreNet platform
|
||||
- CoreNet coherency manager supporting coherent and noncoherent transactions
|
||||
with prioritization and bandwidth allocation amongst CoreNet endpoints
|
||||
- 150 Gbps coherent read bandwidth
|
||||
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
|
||||
- Data Path Acceleration Architecture (DPAA) incorporating acceleration for the following functions:
|
||||
- Packet parsing, classification, and distribution
|
||||
- Queue management for scheduling, packet sequencing, and congestion management
|
||||
- Cryptography Acceleration (SEC 5.x)
|
||||
- IEEE 1588 support
|
||||
- Hardware buffer management for buffer allocation and deallocation
|
||||
- MACSEC on DPAA-based Ethernet ports
|
||||
- Ethernet interfaces
|
||||
- Four 1 Gbps Ethernet controllers
|
||||
- Parallel Ethernet interfaces
|
||||
- Two RGMII interfaces
|
||||
- High speed peripheral interfaces
|
||||
- Three PCI Express 2.0 controllers/ports running at up to 5 GHz
|
||||
- One SATA controller supporting 1.5 and 3.0 Gb/s operation
|
||||
- One QSGMII interface
|
||||
- Four SGMII interface supporting 1000 Mbps
|
||||
- Three SGMII interfaces supporting up to 2500 Mbps
|
||||
- 10GbE XFI or 10Base-KR interface
|
||||
- Additional peripheral interfaces
|
||||
- Two USB 2.0 controllers with integrated PHY
|
||||
- SD/eSDHC/eMMC
|
||||
- eSPI controller
|
||||
- Four I2C controllers
|
||||
- Four UARTs
|
||||
- Four GPIO controllers
|
||||
- Integrated flash controller (IFC)
|
||||
- LCD interface (DIU) with 12 bit dual data rate
|
||||
- Multicore programmable interrupt controller (PIC)
|
||||
- Two 8-channel DMA engines
|
||||
- Single source clocking implementation
|
||||
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
|
||||
- QUICC Engine block
|
||||
- 32-bit RISC controller for flexible support of the communications peripherals
|
||||
- Serial DMA channel for receive and transmit on all serial channels
|
||||
- Two universal communication controllers, supporting TDM, HDLC, and UART
|
||||
|
||||
T1023 Personality
|
||||
------------------
|
||||
T1023 is a reduced personality of T1024 without QUICC Engine, DIU, and
|
||||
unavailable deep sleep. Rest of the blocks are almost same as T1024.
|
||||
Differences between T1024 and T1023
|
||||
Feature T1024 T1023
|
||||
QUICC Engine: yes no
|
||||
DIU: yes no
|
||||
Deep Sleep: yes no
|
||||
I2C controller: 4 3
|
||||
DDR: 64-bit 32-bit
|
||||
IFC: 32-bit 28-bit
|
||||
|
||||
|
||||
T1024QDS board Overview
|
||||
-----------------------
|
||||
- SERDES Connections
|
||||
4 lanes supporting the following:
|
||||
- PCI Express: supports Gen 1 and Gen 2
|
||||
- SGMII 1G and SGMII 2.5G
|
||||
- QSGMII
|
||||
- XFI
|
||||
- SATA 2.0
|
||||
- High-speed multiplexers route the SerDes traffic to appropriate slots or connectors.
|
||||
- Aurora debug with dedicated connectors.
|
||||
- DDR Controller
|
||||
- Supports up to 1600 MTPS data-rate.
|
||||
- Supports one DDR4 or DDR3L module using DDR4 to DDR3L adapter card.
|
||||
- Supports Single-, dual- or quad-rank DIMMs
|
||||
- DDR power supplies 1.35V (DDR3L)/1.20V (DDR4) to all devices with automatic tracking of VTT.
|
||||
- IFC/Local Bus
|
||||
- NAND Flash: 8-bit, async, up to 2GB
|
||||
- NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB
|
||||
- NOR devices support 8 virtual banks
|
||||
- Socketed to allow alternate devices
|
||||
- GASIC: Simple (minimal) target within QIXIS FPGA
|
||||
- PromJET rapid memory download support
|
||||
- IFC Debug/Development card
|
||||
- Ethernet
|
||||
- Two on-board RGMII 10M/100M/1G ethernet ports.
|
||||
- One QSGMII interface
|
||||
- Four SGMII interface supporting 1Gbps
|
||||
- Three SGMII interfaces supporting 2.5Gbps
|
||||
- one 10Gbps XFI or 10Base-KR interface
|
||||
- QIXIS System Logic FPGA
|
||||
- Manages system power and reset sequencing.
|
||||
- Manages the configurations of DUT, board, and clock for dynamic shmoo.
|
||||
- Collects V-I-T data in background for code/power profiling.
|
||||
- Supports legacy TMT test features (POSt, IRS, SYSCLK-synchronous assertion).
|
||||
- General fault monitoring and logging.
|
||||
- Powered from ATX 'standby' power supply that allows continuous operation while rest of the system is off.
|
||||
- Clocks
|
||||
- System and DDR clock (SYSCLK, DDRCLK).
|
||||
- Switch selectable to one of 16 common settings in the interval of 64 MHz-166 MHz.
|
||||
- Software programmable in 1 MHz increments from 1-200 MHz.
|
||||
- SERDES clocks
|
||||
- Provides clocks to SerDes blocks and slots.
|
||||
- 100 MHz, 125 MHz and 156.25 MHz options.
|
||||
- Spread-spectrum option for 100 MHz.
|
||||
- Power Supplies
|
||||
- Dedicated PMBus regulator for VDD and VDDC.
|
||||
- Adjustable from 0.7V to 1.3V at 35A
|
||||
- VDD can be disabled independanty from VDDC for “deep sleep”.
|
||||
- DDR3L/DDR4 power supply for GVDD: 1.35 or 1.20V at up to 22A.
|
||||
- VTT/MVREF automatically track operating voltage.
|
||||
- Dedicated 2.5V VPP supply.
|
||||
- Dedicated regulators/filters for AVDD supplies.
|
||||
- Dedicated regulators for other supplies, for example OVDD, CVDD, DVDD, LVDD, POVDD, and EVDD.
|
||||
- Video
|
||||
- DIU supports video up to 1280x1024x32 bpp.
|
||||
- Chrontel CH7201 for HDMI connection.
|
||||
- TI DS90C387R for direct LCD connection.
|
||||
- Raw (not encoded) video connector for testing or other encoders.
|
||||
- USB
|
||||
- Supports two USB 2.0 ports with integrated PHYs.
|
||||
- Two type A ports with 5V@1.5A per port.
|
||||
- Second port can be converted to OTG mini-AB.
|
||||
- SDHC
|
||||
For T1024QDS, the SDHC port connects directly to an adapter card slot that has the following features:
|
||||
- upport for optional clock feedback paths.
|
||||
- Support for optional high-speed voltage translation direction controls.
|
||||
- Support for SD slots for: SD, SDHC (1x, 4x, 8x) and MMC.
|
||||
- Support for eMMC memory devices.
|
||||
- SPI
|
||||
-On-board support of 3 different devices and sizes.
|
||||
- Other IO
|
||||
- Two Serial ports
|
||||
- ProfiBus port
|
||||
- Four I2C ports
|
||||
|
||||
|
||||
Memory map on T1024QDS
|
||||
----------------------
|
||||
Start Address End Address Description Size
|
||||
0xF_FFDF_0000 0xF_FFDF_0FFF IFC - FPGA 4KB
|
||||
0xF_FF80_0000 0xF_FF80_FFFF IFC - NAND Flash 64KB
|
||||
0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16MB
|
||||
0xF_F802_0000 0xF_F802_FFFF PCI Express 3 I/O Space 64KB
|
||||
0xF_F801_0000 0xF_F801_FFFF PCI Express 2 I/O Space 64KB
|
||||
0xF_F800_0000 0xF_F800_FFFF PCI Express 1 I/O Space 64KB
|
||||
0xF_F600_0000 0xF_F7FF_FFFF Queue manager software portal 32MB
|
||||
0xF_F400_0000 0xF_F5FF_FFFF Buffer manager software portal 32MB
|
||||
0xF_E800_0000 0xF_EFFF_FFFF IFC - NOR Flash 128MB
|
||||
0xF_E000_0000 0xF_E7FF_FFFF Promjet 128MB
|
||||
0xF_0000_0000 0xF_003F_FFFF DCSR 4MB
|
||||
0xC_2000_0000 0xC_2FFF_FFFF PCI Express 3 Mem Space 256MB
|
||||
0xC_1000_0000 0xC_1FFF_FFFF PCI Express 2 Mem Space 256MB
|
||||
0xC_0000_0000 0xC_0FFF_FFFF PCI Express 1 Mem Space 256MB
|
||||
0x0_0000_0000 0x0_ffff_ffff DDR 4GB
|
||||
|
||||
|
||||
128MB NOR Flash memory Map
|
||||
--------------------------
|
||||
Start Address End Address Definition Max size
|
||||
0xEFF40000 0xEFFFFFFF U-Boot (current bank) 768KB
|
||||
0xEFF20000 0xEFF3FFFF U-Boot env (current bank) 128KB
|
||||
0xEFF00000 0xEFF1FFFF FMAN Ucode (current bank) 128KB
|
||||
0xEFE00000 0xEFE3FFFF QE firmware (current bank) 256KB
|
||||
0xED300000 0xEFEFFFFF rootfs (alt bank) 44MB
|
||||
0xEC800000 0xEC8FFFFF Hardware device tree (alt bank) 1MB
|
||||
0xEC020000 0xEC7FFFFF Linux.uImage (alt bank) 7MB + 875KB
|
||||
0xEC000000 0xEC01FFFF RCW (alt bank) 128KB
|
||||
0xEBF40000 0xEBFFFFFF U-Boot (alt bank) 768KB
|
||||
0xEBF20000 0xEBF3FFFF U-Boot env (alt bank) 128KB
|
||||
0xEBF00000 0xEBF1FFFF FMAN ucode (alt bank) 128KB
|
||||
0xEBE00000 0xEBE3FFFF QE firmware (alt bank) 256KB
|
||||
0xE9300000 0xEBEFFFFF rootfs (current bank) 44MB
|
||||
0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 1MB
|
||||
0xE8020000 0xE86FFFFF Linux.uImage (current bank) 7MB + 875KB
|
||||
0xE8000000 0xE801FFFF RCW (current bank) 128KB
|
||||
|
||||
|
||||
SerDes clock vs DIP-switch settings
|
||||
-----------------------------------
|
||||
SRDS_PRTCL_S1 SD1_REF_CLK1 SD1_REF_CLK2 SW4[1:4]
|
||||
0x6F 100MHz 125MHz 1101
|
||||
0xD6 100MHz 100MHz 1111
|
||||
0x99 156.25MHz 100MHz 1011
|
||||
|
||||
|
||||
T1024 Clock frequency
|
||||
----------------------
|
||||
BIN Core DDR Platform FMan
|
||||
Bin1: 1400MHz 1600MT/s 400MHz 700MHz
|
||||
Bin2: 1200MHz 1600MT/s 400MHz 600MHz
|
||||
Bin3: 1000MHz 1600MT/s 400MHz 500MHz
|
||||
|
||||
|
||||
|
||||
Software configurations and board settings
|
||||
------------------------------------------
|
||||
1. NOR boot:
|
||||
a. build NOR boot image
|
||||
$ make T1024QDS_defconfig (For DDR3L, by default)
|
||||
or make T1024QDS_D4_defconfig (For DDR4)
|
||||
$ make
|
||||
b. program u-boot.bin image to NOR flash
|
||||
=> tftp 1000000 u-boot.bin
|
||||
=> pro off all;era eff40000 efffffff;cp.b 1000000 eff40000 $filesize
|
||||
set SW1[1:8] = '00010011', SW2[1] = '1', SW6[1:4] = '0000' for NOR boot
|
||||
|
||||
Switching between default bank0 and alternate bank4 on NOR flash
|
||||
To change boot source to vbank4:
|
||||
via software: run command 'qixis_reset altbank' in U-Boot.
|
||||
via DIP-switch: set SW6[1:4] = '0100'
|
||||
|
||||
To change boot source to vbank0:
|
||||
via software: run command 'qixis_reset' in U-Boot.
|
||||
via DIP-Switch: set SW6[1:4] = '0000'
|
||||
|
||||
2. NAND Boot:
|
||||
a. build PBL image for NAND boot
|
||||
$ make T1024QDS_NAND_defconfig
|
||||
$ make
|
||||
b. program u-boot-with-spl-pbl.bin to NAND flash
|
||||
=> tftp 1000000 u-boot-with-spl-pbl.bin
|
||||
=> nand erase 0 $filesize
|
||||
=> nand write 1000000 0 $filesize
|
||||
set SW1[1:8] = '10000010', SW2[1] = '0' and SW6[1:4] = '1001' for NAND boot
|
||||
|
||||
3. SPI Boot:
|
||||
a. build PBL image for SPI boot
|
||||
$ make T1024QDS_SPIFLASH_defconfig
|
||||
$ make
|
||||
b. program u-boot-with-spl-pbl.bin to SPI flash
|
||||
=> tftp 1000000 u-boot-with-spl-pbl.bin
|
||||
=> sf probe 0
|
||||
=> sf erase 0 f0000
|
||||
=> sf write 1000000 0 $filesize
|
||||
set SW1[1:8] = '00100010', SW2[1] ='1' for SPI boot
|
||||
|
||||
4. SD Boot:
|
||||
a. build PBL image for SD boot
|
||||
$ make T1024QDS_SDCARD_defconfig
|
||||
$ make
|
||||
b. program u-boot-with-spl-pbl.bin to SD/MMC card
|
||||
=> tftp 1000000 u-boot-with-spl-pbl.bin
|
||||
=> mmc write 1000000 8 0x800
|
||||
=> tftp 1000000 fsl_fman_ucode_t1024_xx.bin
|
||||
=> mmc write 1000000 0x820 80
|
||||
set SW1[1:8] = '00100000', SW2[1] = '0' for SD boot
|
||||
|
||||
|
||||
DIU/QE-TDM/SDXC settings
|
||||
-------------------
|
||||
a) For TDM Riser: set pin_mux=tdm in hwconfig
|
||||
b) For UCC(ProfiBus): set pin_mux=ucc in hwconfig
|
||||
c) For HDMI(DVI): set pin_mux=hdmi in hwconfig
|
||||
d) For LCD(DFP): set pin_mux=lcd in hwconfig
|
||||
e) For SDXC: set adaptor=sdxc in hwconfig
|
||||
|
||||
2-stage NAND/SPI/SD boot loader
|
||||
-------------------------------
|
||||
PBL initializes the internal CPC-SRAM and copy SPL(160K) to SRAM.
|
||||
SPL further initializes DDR using SPD and environment variables
|
||||
and copy U-Boot(768 KB) from NAND/SPI/SD device to DDR.
|
||||
Finally SPL transers control to U-Boot for futher booting.
|
||||
|
||||
SPL has following features:
|
||||
- Executes within 256K
|
||||
- No relocation required
|
||||
|
||||
Run time view of SPL framework
|
||||
-------------------------------------------------
|
||||
|Area | Address |
|
||||
-------------------------------------------------
|
||||
|SecureBoot header | 0xFFFC0000 (32KB) |
|
||||
-------------------------------------------------
|
||||
|GD, BD | 0xFFFC8000 (4KB) |
|
||||
-------------------------------------------------
|
||||
|ENV | 0xFFFC9000 (8KB) |
|
||||
-------------------------------------------------
|
||||
|HEAP | 0xFFFCB000 (30KB) |
|
||||
-------------------------------------------------
|
||||
|STACK | 0xFFFD8000 (22KB) |
|
||||
-------------------------------------------------
|
||||
|U-Boot SPL | 0xFFFD8000 (160KB) |
|
||||
-------------------------------------------------
|
||||
|
||||
NAND Flash memory Map on T1024QDS
|
||||
-------------------------------------------------------------
|
||||
Start End Definition Size
|
||||
0x000000 0x0FFFFF U-Boot 1MB
|
||||
0x100000 0x15FFFF U-Boot env 8KB
|
||||
0x160000 0x17FFFF FMAN Ucode 128KB
|
||||
0x180000 0x19FFFF QE Firmware 128KB
|
||||
|
||||
|
||||
SD Card memory Map on T1024QDS
|
||||
----------------------------------------------------
|
||||
Block #blocks Definition Size
|
||||
0x008 2048 U-Boot img 1MB
|
||||
0x800 0016 U-Boot env 8KB
|
||||
0x820 0256 FMAN Ucode 128KB
|
||||
0x920 0256 QE Firmware 128KB
|
||||
|
||||
|
||||
SPI Flash memory Map on T1024QDS
|
||||
----------------------------------------------------
|
||||
Start End Definition Size
|
||||
0x000000 0x0FFFFF U-Boot img 1MB
|
||||
0x100000 0x101FFF U-Boot env 8KB
|
||||
0x110000 0x12FFFF FMAN Ucode 128KB
|
||||
0x130000 0x14FFFF QE Firmware 128KB
|
||||
|
||||
|
||||
For more details, please refer to T1024QDS Reference Manual and access
|
||||
website www.freescale.com and Freescale QorIQ SDK Infocenter document.
|
||||
@@ -1,195 +0,0 @@
|
||||
// SPDX-License-Identifier: GPL-2.0+
|
||||
/*
|
||||
* Copyright 2014 Freescale Semiconductor, Inc.
|
||||
*/
|
||||
|
||||
#include <common.h>
|
||||
#include <i2c.h>
|
||||
#include <hwconfig.h>
|
||||
#include <init.h>
|
||||
#include <log.h>
|
||||
#include <asm/mmu.h>
|
||||
#include <fsl_ddr_sdram.h>
|
||||
#include <fsl_ddr_dimm_params.h>
|
||||
#include <asm/fsl_law.h>
|
||||
#include <asm/mpc85xx_gpio.h>
|
||||
#include <linux/delay.h>
|
||||
|
||||
DECLARE_GLOBAL_DATA_PTR;
|
||||
|
||||
struct board_specific_parameters {
|
||||
u32 n_ranks;
|
||||
u32 datarate_mhz_high;
|
||||
u32 rank_gb;
|
||||
u32 clk_adjust;
|
||||
u32 wrlvl_start;
|
||||
u32 wrlvl_ctl_2;
|
||||
u32 wrlvl_ctl_3;
|
||||
};
|
||||
|
||||
/*
|
||||
* datarate_mhz_high values need to be in ascending order
|
||||
*/
|
||||
static const struct board_specific_parameters udimm0[] = {
|
||||
/*
|
||||
* memory controller 0
|
||||
* num| hi| rank| clk| wrlvl | wrlvl | wrlvl |
|
||||
* ranks| mhz| GB |adjst| start | ctl2 | ctl3 |
|
||||
*/
|
||||
#if defined(CONFIG_SYS_FSL_DDR4)
|
||||
{2, 1666, 0, 8, 7, 0x0808090B, 0x0C0D0E0A,},
|
||||
{2, 1900, 0, 8, 6, 0x08080A0C, 0x0D0E0F0A,},
|
||||
{1, 1666, 0, 8, 6, 0x0708090B, 0x0C0D0E09,},
|
||||
{1, 1900, 0, 8, 6, 0x08080A0C, 0x0D0E0F0A,},
|
||||
{1, 2200, 0, 8, 7, 0x08090A0D, 0x0F0F100C,},
|
||||
#elif defined(CONFIG_SYS_FSL_DDR3)
|
||||
{2, 833, 0, 8, 6, 0x06060607, 0x08080807,},
|
||||
{2, 1350, 0, 8, 7, 0x0708080A, 0x0A0B0C09,},
|
||||
{2, 1666, 0, 8, 7, 0x0808090B, 0x0C0D0E0A,},
|
||||
{1, 833, 0, 8, 6, 0x06060607, 0x08080807,},
|
||||
{1, 1350, 0, 8, 7, 0x0708080A, 0x0A0B0C09,},
|
||||
{1, 1666, 0, 8, 7, 0x0808090B, 0x0C0D0E0A,},
|
||||
#else
|
||||
#error DDR type not defined
|
||||
#endif
|
||||
{}
|
||||
};
|
||||
|
||||
static const struct board_specific_parameters *udimms[] = {
|
||||
udimm0,
|
||||
};
|
||||
|
||||
void fsl_ddr_board_options(memctl_options_t *popts,
|
||||
dimm_params_t *pdimm,
|
||||
unsigned int ctrl_num)
|
||||
{
|
||||
const struct board_specific_parameters *pbsp, *pbsp_highest = NULL;
|
||||
ulong ddr_freq;
|
||||
struct cpu_type *cpu = gd->arch.cpu;
|
||||
|
||||
if (ctrl_num > 2) {
|
||||
printf("Not supported controller number %d\n", ctrl_num);
|
||||
return;
|
||||
}
|
||||
if (!pdimm->n_ranks)
|
||||
return;
|
||||
|
||||
pbsp = udimms[0];
|
||||
|
||||
/* Get clk_adjust according to the board ddr freqency and n_banks
|
||||
* specified in board_specific_parameters table.
|
||||
*/
|
||||
ddr_freq = get_ddr_freq(0) / 1000000;
|
||||
while (pbsp->datarate_mhz_high) {
|
||||
if (pbsp->n_ranks == pdimm->n_ranks &&
|
||||
(pdimm->rank_density >> 30) >= pbsp->rank_gb) {
|
||||
if (ddr_freq <= pbsp->datarate_mhz_high) {
|
||||
popts->clk_adjust = pbsp->clk_adjust;
|
||||
popts->wrlvl_start = pbsp->wrlvl_start;
|
||||
popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
|
||||
popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
|
||||
goto found;
|
||||
}
|
||||
pbsp_highest = pbsp;
|
||||
}
|
||||
pbsp++;
|
||||
}
|
||||
|
||||
if (pbsp_highest) {
|
||||
printf("Error: board specific timing not found\n");
|
||||
printf("for data rate %lu MT/s\n", ddr_freq);
|
||||
printf("Trying to use the highest speed (%u) parameters\n",
|
||||
pbsp_highest->datarate_mhz_high);
|
||||
popts->clk_adjust = pbsp_highest->clk_adjust;
|
||||
popts->wrlvl_start = pbsp_highest->wrlvl_start;
|
||||
popts->wrlvl_ctl_2 = pbsp->wrlvl_ctl_2;
|
||||
popts->wrlvl_ctl_3 = pbsp->wrlvl_ctl_3;
|
||||
} else {
|
||||
panic("DIMM is not supported by this board");
|
||||
}
|
||||
found:
|
||||
debug("Found timing match: n_ranks %d, data rate %d, rank_gb %d\n",
|
||||
pbsp->n_ranks, pbsp->datarate_mhz_high, pbsp->rank_gb);
|
||||
debug("\tclk_adjust %d, wrlvl_start %d, wrlvl_ctrl_2 0x%x, ",
|
||||
pbsp->clk_adjust, pbsp->wrlvl_start, pbsp->wrlvl_ctl_2);
|
||||
debug("wrlvl_ctrl_3 0x%x\n", pbsp->wrlvl_ctl_3);
|
||||
|
||||
/*
|
||||
* Factors to consider for half-strength driver enable:
|
||||
* - number of DIMMs installed
|
||||
*/
|
||||
popts->half_strength_driver_enable = 1;
|
||||
/*
|
||||
* Write leveling override
|
||||
*/
|
||||
popts->wrlvl_override = 1;
|
||||
popts->wrlvl_sample = 0xf;
|
||||
|
||||
/*
|
||||
* rtt and rtt_wr override
|
||||
*/
|
||||
popts->rtt_override = 0;
|
||||
|
||||
/* Enable ZQ calibration */
|
||||
popts->zq_en = 1;
|
||||
|
||||
/* DHC_EN =1, ODT = 75 Ohm */
|
||||
#ifdef CONFIG_SYS_FSL_DDR4
|
||||
popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_80ohm);
|
||||
popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_80ohm) |
|
||||
DDR_CDR2_VREF_OVRD(70); /* Vref = 70% */
|
||||
#else
|
||||
popts->ddr_cdr1 = DDR_CDR1_DHC_EN | DDR_CDR1_ODT(DDR_CDR_ODT_75ohm);
|
||||
popts->ddr_cdr2 = DDR_CDR2_ODT(DDR_CDR_ODT_75ohm);
|
||||
|
||||
/* optimize cpo for erratum A-009942 */
|
||||
popts->cpo_sample = 0x5f;
|
||||
#endif
|
||||
|
||||
/* T1023 supports max DDR bus 32bit width, T1024 supports DDR 64bit,
|
||||
* set DDR bus width to 32bit for T1023
|
||||
*/
|
||||
if (cpu->soc_ver == SVR_T1023)
|
||||
popts->data_bus_width = DDR_DATA_BUS_WIDTH_32;
|
||||
|
||||
#ifdef CONFIG_FORCE_DDR_DATA_BUS_WIDTH_32
|
||||
/* for DDR bus 32bit test on T1024 */
|
||||
popts->data_bus_width = DDR_DATA_BUS_WIDTH_32;
|
||||
#endif
|
||||
}
|
||||
|
||||
#if defined(CONFIG_DEEP_SLEEP)
|
||||
void board_mem_sleep_setup(void)
|
||||
{
|
||||
void __iomem *qixis_base = (void *)QIXIS_BASE;
|
||||
|
||||
/* does not provide HW signals for power management */
|
||||
clrbits_8(qixis_base + 0x21, 0x2);
|
||||
/* Disable MCKE isolation */
|
||||
gpio_set_value(2, 0);
|
||||
udelay(1);
|
||||
}
|
||||
#endif
|
||||
|
||||
int dram_init(void)
|
||||
{
|
||||
phys_size_t dram_size;
|
||||
|
||||
#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_RAMBOOT_PBL)
|
||||
puts("Initializing....using SPD\n");
|
||||
dram_size = fsl_ddr_sdram();
|
||||
#else
|
||||
/* DDR has been initialised by first stage boot loader */
|
||||
dram_size = fsl_ddr_sdram_size();
|
||||
#endif
|
||||
dram_size = setup_ddr_tlbs(dram_size / 0x100000);
|
||||
dram_size *= 0x100000;
|
||||
|
||||
#if defined(CONFIG_DEEP_SLEEP) && !defined(CONFIG_SPL_BUILD)
|
||||
fsl_dp_resume();
|
||||
#endif
|
||||
|
||||
gd->ram_size = dram_size;
|
||||
|
||||
return 0;
|
||||
}
|
||||
@@ -1,445 +0,0 @@
|
||||
// SPDX-License-Identifier: GPL-2.0+
|
||||
/*
|
||||
* Copyright 2014 Freescale Semiconductor, Inc.
|
||||
*
|
||||
* Shengzhou Liu <Shengzhou.Liu@freescale.com>
|
||||
*/
|
||||
|
||||
#include <common.h>
|
||||
#include <command.h>
|
||||
#include <fdt_support.h>
|
||||
#include <log.h>
|
||||
#include <net.h>
|
||||
#include <netdev.h>
|
||||
#include <asm/mmu.h>
|
||||
#include <asm/processor.h>
|
||||
#include <asm/immap_85xx.h>
|
||||
#include <asm/fsl_law.h>
|
||||
#include <asm/fsl_serdes.h>
|
||||
#include <asm/fsl_portals.h>
|
||||
#include <asm/fsl_liodn.h>
|
||||
#include <malloc.h>
|
||||
#include <fm_eth.h>
|
||||
#include <fsl_mdio.h>
|
||||
#include <miiphy.h>
|
||||
#include <phy.h>
|
||||
#include <fsl_dtsec.h>
|
||||
#include <asm/fsl_serdes.h>
|
||||
#include "../common/qixis.h"
|
||||
#include "../common/fman.h"
|
||||
#include "t102xqds_qixis.h"
|
||||
|
||||
#define EMI_NONE 0xFFFFFFFF
|
||||
#define EMI1_RGMII1 0
|
||||
#define EMI1_RGMII2 1
|
||||
#define EMI1_SLOT1 2
|
||||
#define EMI1_SLOT2 3
|
||||
#define EMI1_SLOT3 4
|
||||
#define EMI1_SLOT4 5
|
||||
#define EMI1_SLOT5 6
|
||||
#define EMI2 7
|
||||
|
||||
static int mdio_mux[NUM_FM_PORTS];
|
||||
|
||||
static const char * const mdio_names[] = {
|
||||
"T1024QDS_MDIO_RGMII1",
|
||||
"T1024QDS_MDIO_RGMII2",
|
||||
"T1024QDS_MDIO_SLOT1",
|
||||
"T1024QDS_MDIO_SLOT2",
|
||||
"T1024QDS_MDIO_SLOT3",
|
||||
"T1024QDS_MDIO_SLOT4",
|
||||
"T1024QDS_MDIO_SLOT5",
|
||||
"T1024QDS_MDIO_10GC",
|
||||
"NULL",
|
||||
};
|
||||
|
||||
/* Map SerDes1 4 lanes to default slot, will be initialized dynamically */
|
||||
static u8 lane_to_slot[] = {2, 3, 4, 5};
|
||||
|
||||
static const char *t1024qds_mdio_name_for_muxval(u8 muxval)
|
||||
{
|
||||
return mdio_names[muxval];
|
||||
}
|
||||
|
||||
struct mii_dev *mii_dev_for_muxval(u8 muxval)
|
||||
{
|
||||
struct mii_dev *bus;
|
||||
const char *name;
|
||||
|
||||
if (muxval > EMI2)
|
||||
return NULL;
|
||||
|
||||
name = t1024qds_mdio_name_for_muxval(muxval);
|
||||
|
||||
if (!name) {
|
||||
printf("No bus for muxval %x\n", muxval);
|
||||
return NULL;
|
||||
}
|
||||
|
||||
bus = miiphy_get_dev_by_name(name);
|
||||
|
||||
if (!bus) {
|
||||
printf("No bus by name %s\n", name);
|
||||
return NULL;
|
||||
}
|
||||
|
||||
return bus;
|
||||
}
|
||||
|
||||
struct t1024qds_mdio {
|
||||
u8 muxval;
|
||||
struct mii_dev *realbus;
|
||||
};
|
||||
|
||||
static void t1024qds_mux_mdio(u8 muxval)
|
||||
{
|
||||
u8 brdcfg4;
|
||||
|
||||
if (muxval < 7) {
|
||||
brdcfg4 = QIXIS_READ(brdcfg[4]);
|
||||
brdcfg4 &= ~BRDCFG4_EMISEL_MASK;
|
||||
brdcfg4 |= (muxval << BRDCFG4_EMISEL_SHIFT);
|
||||
QIXIS_WRITE(brdcfg[4], brdcfg4);
|
||||
}
|
||||
}
|
||||
|
||||
static int t1024qds_mdio_read(struct mii_dev *bus, int addr, int devad,
|
||||
int regnum)
|
||||
{
|
||||
struct t1024qds_mdio *priv = bus->priv;
|
||||
|
||||
t1024qds_mux_mdio(priv->muxval);
|
||||
|
||||
return priv->realbus->read(priv->realbus, addr, devad, regnum);
|
||||
}
|
||||
|
||||
static int t1024qds_mdio_write(struct mii_dev *bus, int addr, int devad,
|
||||
int regnum, u16 value)
|
||||
{
|
||||
struct t1024qds_mdio *priv = bus->priv;
|
||||
|
||||
t1024qds_mux_mdio(priv->muxval);
|
||||
|
||||
return priv->realbus->write(priv->realbus, addr, devad, regnum, value);
|
||||
}
|
||||
|
||||
static int t1024qds_mdio_reset(struct mii_dev *bus)
|
||||
{
|
||||
struct t1024qds_mdio *priv = bus->priv;
|
||||
|
||||
return priv->realbus->reset(priv->realbus);
|
||||
}
|
||||
|
||||
static int t1024qds_mdio_init(char *realbusname, u8 muxval)
|
||||
{
|
||||
struct t1024qds_mdio *pmdio;
|
||||
struct mii_dev *bus = mdio_alloc();
|
||||
|
||||
if (!bus) {
|
||||
printf("Failed to allocate t1024qds MDIO bus\n");
|
||||
return -1;
|
||||
}
|
||||
|
||||
pmdio = malloc(sizeof(*pmdio));
|
||||
if (!pmdio) {
|
||||
printf("Failed to allocate t1024qds private data\n");
|
||||
free(bus);
|
||||
return -1;
|
||||
}
|
||||
|
||||
bus->read = t1024qds_mdio_read;
|
||||
bus->write = t1024qds_mdio_write;
|
||||
bus->reset = t1024qds_mdio_reset;
|
||||
strcpy(bus->name, t1024qds_mdio_name_for_muxval(muxval));
|
||||
|
||||
pmdio->realbus = miiphy_get_dev_by_name(realbusname);
|
||||
|
||||
if (!pmdio->realbus) {
|
||||
printf("No bus with name %s\n", realbusname);
|
||||
free(bus);
|
||||
free(pmdio);
|
||||
return -1;
|
||||
}
|
||||
|
||||
pmdio->muxval = muxval;
|
||||
bus->priv = pmdio;
|
||||
return mdio_register(bus);
|
||||
}
|
||||
|
||||
void board_ft_fman_fixup_port(void *fdt, char *compat, phys_addr_t addr,
|
||||
enum fm_port port, int offset)
|
||||
{
|
||||
struct fixed_link f_link;
|
||||
|
||||
if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_RGMII) {
|
||||
if (port == FM1_DTSEC3) {
|
||||
fdt_set_phy_handle(fdt, compat, addr, "rgmii_phy2");
|
||||
fdt_setprop_string(fdt, offset, "phy-connection-type",
|
||||
"rgmii");
|
||||
fdt_status_okay_by_alias(fdt, "emi1_rgmii1");
|
||||
}
|
||||
} else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII) {
|
||||
if (port == FM1_DTSEC1) {
|
||||
fdt_set_phy_handle(fdt, compat, addr,
|
||||
"sgmii_vsc8234_phy_s5");
|
||||
} else if (port == FM1_DTSEC2) {
|
||||
fdt_set_phy_handle(fdt, compat, addr,
|
||||
"sgmii_vsc8234_phy_s4");
|
||||
}
|
||||
} else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_SGMII_2500) {
|
||||
if (port == FM1_DTSEC3) {
|
||||
fdt_set_phy_handle(fdt, compat, addr,
|
||||
"sgmii_aqr105_phy_s3");
|
||||
}
|
||||
} else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_QSGMII) {
|
||||
switch (port) {
|
||||
case FM1_DTSEC1:
|
||||
fdt_set_phy_handle(fdt, compat, addr, "qsgmii_phy_p1");
|
||||
break;
|
||||
case FM1_DTSEC2:
|
||||
fdt_set_phy_handle(fdt, compat, addr, "qsgmii_phy_p2");
|
||||
break;
|
||||
case FM1_DTSEC3:
|
||||
fdt_set_phy_handle(fdt, compat, addr, "qsgmii_phy_p3");
|
||||
break;
|
||||
case FM1_DTSEC4:
|
||||
fdt_set_phy_handle(fdt, compat, addr, "qsgmii_phy_p4");
|
||||
break;
|
||||
default:
|
||||
break;
|
||||
}
|
||||
fdt_delprop(fdt, offset, "phy-connection-type");
|
||||
fdt_setprop_string(fdt, offset, "phy-connection-type",
|
||||
"qsgmii");
|
||||
fdt_status_okay_by_alias(fdt, "emi1_slot2");
|
||||
} else if (fm_info_get_enet_if(port) == PHY_INTERFACE_MODE_XGMII) {
|
||||
/* XFI interface */
|
||||
f_link.phy_id = port;
|
||||
f_link.duplex = 1;
|
||||
f_link.link_speed = 10000;
|
||||
f_link.pause = 0;
|
||||
f_link.asym_pause = 0;
|
||||
/* no PHY for XFI */
|
||||
fdt_delprop(fdt, offset, "phy-handle");
|
||||
fdt_setprop(fdt, offset, "fixed-link", &f_link, sizeof(f_link));
|
||||
fdt_setprop_string(fdt, offset, "phy-connection-type", "xgmii");
|
||||
}
|
||||
}
|
||||
|
||||
void fdt_fixup_board_enet(void *fdt)
|
||||
{
|
||||
}
|
||||
|
||||
/*
|
||||
* This function reads RCW to check if Serdes1{A:D} is configured
|
||||
* to slot 1/2/3/4/5 and update the lane_to_slot[] array accordingly
|
||||
*/
|
||||
static void initialize_lane_to_slot(void)
|
||||
{
|
||||
ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
|
||||
u32 srds_s1 = in_be32(&gur->rcwsr[4]) &
|
||||
FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
|
||||
|
||||
srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
|
||||
|
||||
switch (srds_s1) {
|
||||
case 0x46:
|
||||
case 0x47:
|
||||
lane_to_slot[1] = 2;
|
||||
break;
|
||||
default:
|
||||
break;
|
||||
}
|
||||
}
|
||||
|
||||
int board_eth_init(bd_t *bis)
|
||||
{
|
||||
#if defined(CONFIG_FMAN_ENET)
|
||||
int i, idx, lane, slot, interface;
|
||||
struct memac_mdio_info dtsec_mdio_info;
|
||||
struct memac_mdio_info tgec_mdio_info;
|
||||
ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
|
||||
u32 srds_s1;
|
||||
|
||||
srds_s1 = in_be32(&gur->rcwsr[4]) &
|
||||
FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
|
||||
srds_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
|
||||
|
||||
initialize_lane_to_slot();
|
||||
|
||||
/* Initialize the mdio_mux array so we can recognize empty elements */
|
||||
for (i = 0; i < NUM_FM_PORTS; i++)
|
||||
mdio_mux[i] = EMI_NONE;
|
||||
|
||||
dtsec_mdio_info.regs =
|
||||
(struct memac_mdio_controller *)CONFIG_SYS_FM1_DTSEC_MDIO_ADDR;
|
||||
|
||||
dtsec_mdio_info.name = DEFAULT_FM_MDIO_NAME;
|
||||
|
||||
/* Register the 1G MDIO bus */
|
||||
fm_memac_mdio_init(bis, &dtsec_mdio_info);
|
||||
|
||||
tgec_mdio_info.regs =
|
||||
(struct memac_mdio_controller *)CONFIG_SYS_FM1_TGEC_MDIO_ADDR;
|
||||
tgec_mdio_info.name = DEFAULT_FM_TGEC_MDIO_NAME;
|
||||
|
||||
/* Register the 10G MDIO bus */
|
||||
fm_memac_mdio_init(bis, &tgec_mdio_info);
|
||||
|
||||
/* Register the muxing front-ends to the MDIO buses */
|
||||
t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII1);
|
||||
t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_RGMII2);
|
||||
t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT1);
|
||||
t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT2);
|
||||
t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT3);
|
||||
t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT4);
|
||||
t1024qds_mdio_init(DEFAULT_FM_MDIO_NAME, EMI1_SLOT5);
|
||||
t1024qds_mdio_init(DEFAULT_FM_TGEC_MDIO_NAME, EMI2);
|
||||
|
||||
/* Set the two on-board RGMII PHY address */
|
||||
fm_info_set_phy_address(FM1_DTSEC3, RGMII_PHY2_ADDR);
|
||||
fm_info_set_phy_address(FM1_DTSEC4, RGMII_PHY1_ADDR);
|
||||
|
||||
switch (srds_s1) {
|
||||
case 0xd5:
|
||||
case 0xd6:
|
||||
/* QSGMII in Slot2 */
|
||||
fm_info_set_phy_address(FM1_DTSEC1, 0x8);
|
||||
fm_info_set_phy_address(FM1_DTSEC2, 0x9);
|
||||
fm_info_set_phy_address(FM1_DTSEC3, 0xa);
|
||||
fm_info_set_phy_address(FM1_DTSEC4, 0xb);
|
||||
break;
|
||||
case 0x95:
|
||||
case 0x99:
|
||||
/*
|
||||
* XFI does not need a PHY to work, but to avoid U-Boot use
|
||||
* default PHY address which is zero to a MAC when it found
|
||||
* a MAC has no PHY address, we give a PHY address to XFI
|
||||
* MAC, and should not use a real XAUI PHY address, since
|
||||
* MDIO can access it successfully, and then MDIO thinks the
|
||||
* XAUI card is used for the XFI MAC, which will cause error.
|
||||
*/
|
||||
fm_info_set_phy_address(FM1_10GEC1, 4);
|
||||
fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR);
|
||||
break;
|
||||
case 0x6f:
|
||||
/* SGMII in Slot3, Slot4, Slot5 */
|
||||
fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_AQ_PHY_ADDR_S5);
|
||||
fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_AQ_PHY_ADDR_S4);
|
||||
fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_PORT1_PHY_ADDR);
|
||||
break;
|
||||
case 0x7f:
|
||||
fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_AQ_PHY_ADDR_S5);
|
||||
fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_AQ_PHY_ADDR_S4);
|
||||
fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_AQ_PHY_ADDR_S3);
|
||||
break;
|
||||
case 0x47:
|
||||
fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR);
|
||||
break;
|
||||
case 0x77:
|
||||
fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR);
|
||||
fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_AQ_PHY_ADDR_S3);
|
||||
break;
|
||||
case 0x5a:
|
||||
fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR);
|
||||
break;
|
||||
case 0x6a:
|
||||
fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR);
|
||||
fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_PORT1_PHY_ADDR);
|
||||
break;
|
||||
case 0x5b:
|
||||
fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR);
|
||||
fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR);
|
||||
break;
|
||||
case 0x6b:
|
||||
fm_info_set_phy_address(FM1_DTSEC1, SGMII_CARD_PORT1_PHY_ADDR);
|
||||
fm_info_set_phy_address(FM1_DTSEC2, SGMII_CARD_PORT1_PHY_ADDR);
|
||||
fm_info_set_phy_address(FM1_DTSEC3, SGMII_CARD_PORT1_PHY_ADDR);
|
||||
break;
|
||||
default:
|
||||
break;
|
||||
}
|
||||
|
||||
for (i = FM1_DTSEC1; i < FM1_DTSEC1 + CONFIG_SYS_NUM_FM1_DTSEC; i++) {
|
||||
idx = i - FM1_DTSEC1;
|
||||
interface = fm_info_get_enet_if(i);
|
||||
switch (interface) {
|
||||
case PHY_INTERFACE_MODE_SGMII:
|
||||
case PHY_INTERFACE_MODE_SGMII_2500:
|
||||
case PHY_INTERFACE_MODE_QSGMII:
|
||||
if (interface == PHY_INTERFACE_MODE_SGMII) {
|
||||
lane = serdes_get_first_lane(FSL_SRDS_1,
|
||||
SGMII_FM1_DTSEC1 + idx);
|
||||
} else if (interface == PHY_INTERFACE_MODE_SGMII_2500) {
|
||||
lane = serdes_get_first_lane(FSL_SRDS_1,
|
||||
SGMII_2500_FM1_DTSEC1 + idx);
|
||||
} else {
|
||||
lane = serdes_get_first_lane(FSL_SRDS_1,
|
||||
QSGMII_FM1_A);
|
||||
}
|
||||
|
||||
if (lane < 0)
|
||||
break;
|
||||
|
||||
slot = lane_to_slot[lane];
|
||||
debug("FM1@DTSEC%u expects SGMII in slot %u\n",
|
||||
idx + 1, slot);
|
||||
if (QIXIS_READ(present2) & (1 << (slot - 1)))
|
||||
fm_disable_port(i);
|
||||
|
||||
switch (slot) {
|
||||
case 2:
|
||||
mdio_mux[i] = EMI1_SLOT2;
|
||||
fm_info_set_mdio(i, mii_dev_for_muxval(
|
||||
mdio_mux[i]));
|
||||
break;
|
||||
case 3:
|
||||
mdio_mux[i] = EMI1_SLOT3;
|
||||
fm_info_set_mdio(i, mii_dev_for_muxval(
|
||||
mdio_mux[i]));
|
||||
break;
|
||||
case 4:
|
||||
mdio_mux[i] = EMI1_SLOT4;
|
||||
fm_info_set_mdio(i, mii_dev_for_muxval(
|
||||
mdio_mux[i]));
|
||||
break;
|
||||
case 5:
|
||||
mdio_mux[i] = EMI1_SLOT5;
|
||||
fm_info_set_mdio(i, mii_dev_for_muxval(
|
||||
mdio_mux[i]));
|
||||
break;
|
||||
}
|
||||
break;
|
||||
case PHY_INTERFACE_MODE_RGMII:
|
||||
if (i == FM1_DTSEC3)
|
||||
mdio_mux[i] = EMI1_RGMII2;
|
||||
else if (i == FM1_DTSEC4)
|
||||
mdio_mux[i] = EMI1_RGMII1;
|
||||
fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i]));
|
||||
break;
|
||||
default:
|
||||
break;
|
||||
}
|
||||
}
|
||||
|
||||
for (i = FM1_10GEC1; i < FM1_10GEC1 + CONFIG_SYS_NUM_FM1_10GEC; i++) {
|
||||
idx = i - FM1_10GEC1;
|
||||
switch (fm_info_get_enet_if(i)) {
|
||||
case PHY_INTERFACE_MODE_XGMII:
|
||||
lane = serdes_get_first_lane(FSL_SRDS_1,
|
||||
XFI_FM1_MAC1 + idx);
|
||||
if (lane < 0)
|
||||
break;
|
||||
mdio_mux[i] = EMI2;
|
||||
fm_info_set_mdio(i, mii_dev_for_muxval(mdio_mux[i]));
|
||||
break;
|
||||
default:
|
||||
break;
|
||||
}
|
||||
}
|
||||
|
||||
cpu_eth_init(bis);
|
||||
#endif /* CONFIG_FMAN_ENET */
|
||||
|
||||
return pci_eth_init(bis);
|
||||
}
|
||||
@@ -1,31 +0,0 @@
|
||||
// SPDX-License-Identifier: GPL-2.0+
|
||||
/*
|
||||
* Copyright 2014 Freescale Semiconductor, Inc.
|
||||
*/
|
||||
|
||||
#include <common.h>
|
||||
#include <asm/fsl_law.h>
|
||||
#include <asm/mmu.h>
|
||||
|
||||
struct law_entry law_table[] = {
|
||||
#ifdef CONFIG_MTD_NOR_FLASH
|
||||
SET_LAW(CONFIG_SYS_FLASH_BASE_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_IFC),
|
||||
#endif
|
||||
#ifdef CONFIG_SYS_BMAN_MEM_PHYS
|
||||
SET_LAW(CONFIG_SYS_BMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_BMAN),
|
||||
#endif
|
||||
#ifdef CONFIG_SYS_QMAN_MEM_PHYS
|
||||
SET_LAW(CONFIG_SYS_QMAN_MEM_PHYS, LAW_SIZE_32M, LAW_TRGT_IF_QMAN),
|
||||
#endif
|
||||
#ifdef QIXIS_BASE_PHYS
|
||||
SET_LAW(QIXIS_BASE_PHYS, LAW_SIZE_4K, LAW_TRGT_IF_IFC),
|
||||
#endif
|
||||
#ifdef CONFIG_SYS_DCSRBAR_PHYS
|
||||
SET_LAW(CONFIG_SYS_DCSRBAR_PHYS, LAW_SIZE_4M, LAW_TRGT_IF_DCSR),
|
||||
#endif
|
||||
#ifdef CONFIG_SYS_NAND_BASE_PHYS
|
||||
SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_IFC),
|
||||
#endif
|
||||
};
|
||||
|
||||
int num_law_entries = ARRAY_SIZE(law_table);
|
||||
@@ -1,23 +0,0 @@
|
||||
// SPDX-License-Identifier: GPL-2.0+
|
||||
/*
|
||||
* Copyright 2014 Freescale Semiconductor, Inc.
|
||||
*/
|
||||
|
||||
#include <common.h>
|
||||
#include <command.h>
|
||||
#include <init.h>
|
||||
#include <pci.h>
|
||||
#include <asm/fsl_pci.h>
|
||||
#include <linux/libfdt.h>
|
||||
#include <fdt_support.h>
|
||||
#include <asm/fsl_serdes.h>
|
||||
|
||||
void pci_init_board(void)
|
||||
{
|
||||
fsl_pcie_init_board(0);
|
||||
}
|
||||
|
||||
void pci_of_setup(void *blob, bd_t *bd)
|
||||
{
|
||||
FT_FSL_PCI_SETUP;
|
||||
}
|
||||
@@ -1,156 +0,0 @@
|
||||
// SPDX-License-Identifier: GPL-2.0+
|
||||
/* Copyright 2014 Freescale Semiconductor, Inc.
|
||||
*/
|
||||
|
||||
#include <common.h>
|
||||
#include <clock_legacy.h>
|
||||
#include <console.h>
|
||||
#include <env_internal.h>
|
||||
#include <init.h>
|
||||
#include <malloc.h>
|
||||
#include <ns16550.h>
|
||||
#include <nand.h>
|
||||
#include <i2c.h>
|
||||
#include <mmc.h>
|
||||
#include <fsl_esdhc.h>
|
||||
#include <spi_flash.h>
|
||||
#include "../common/qixis.h"
|
||||
#include "t102xqds_qixis.h"
|
||||
#include "../common/spl.h"
|
||||
|
||||
DECLARE_GLOBAL_DATA_PTR;
|
||||
|
||||
phys_size_t get_effective_memsize(void)
|
||||
{
|
||||
return CONFIG_SYS_L3_SIZE;
|
||||
}
|
||||
|
||||
unsigned long get_board_sys_clk(void)
|
||||
{
|
||||
u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
|
||||
|
||||
switch (sysclk_conf & 0x0F) {
|
||||
case QIXIS_SYSCLK_83:
|
||||
return 83333333;
|
||||
case QIXIS_SYSCLK_100:
|
||||
return 100000000;
|
||||
case QIXIS_SYSCLK_125:
|
||||
return 125000000;
|
||||
case QIXIS_SYSCLK_133:
|
||||
return 133333333;
|
||||
case QIXIS_SYSCLK_150:
|
||||
return 150000000;
|
||||
case QIXIS_SYSCLK_160:
|
||||
return 160000000;
|
||||
case QIXIS_SYSCLK_166:
|
||||
return 166666666;
|
||||
}
|
||||
return 66666666;
|
||||
}
|
||||
|
||||
unsigned long get_board_ddr_clk(void)
|
||||
{
|
||||
u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
|
||||
|
||||
switch ((ddrclk_conf & 0x30) >> 4) {
|
||||
case QIXIS_DDRCLK_100:
|
||||
return 100000000;
|
||||
case QIXIS_DDRCLK_125:
|
||||
return 125000000;
|
||||
case QIXIS_DDRCLK_133:
|
||||
return 133333333;
|
||||
}
|
||||
return 66666666;
|
||||
}
|
||||
|
||||
void board_init_f(ulong bootflag)
|
||||
{
|
||||
u32 plat_ratio, sys_clk, ccb_clk;
|
||||
ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
|
||||
|
||||
#if defined(CONFIG_ARCH_T1040) && defined(CONFIG_SPL_NAND_BOOT)
|
||||
/*
|
||||
* There is T1040 SoC issue where NOR, FPGA are inaccessible during
|
||||
* NAND boot because IFC signals > IFC_AD7 are not enabled.
|
||||
* This workaround changes RCW source to make all signals enabled.
|
||||
*/
|
||||
u32 porsr1, pinctl;
|
||||
#define FSL_CORENET_CCSR_PORSR1_RCW_MASK 0xFF800000
|
||||
|
||||
porsr1 = in_be32(&gur->porsr1);
|
||||
pinctl = ((porsr1 & ~(FSL_CORENET_CCSR_PORSR1_RCW_MASK)) | 0x24800000);
|
||||
out_be32((unsigned int *)(CONFIG_SYS_DCSRBAR + 0x20000), pinctl);
|
||||
#endif
|
||||
|
||||
/* Memcpy existing GD at CONFIG_SPL_GD_ADDR */
|
||||
memcpy((void *)CONFIG_SPL_GD_ADDR, (void *)gd, sizeof(gd_t));
|
||||
|
||||
/* Update GD pointer */
|
||||
gd = (gd_t *)(CONFIG_SPL_GD_ADDR);
|
||||
|
||||
console_init_f();
|
||||
|
||||
/* initialize selected port with appropriate baud rate */
|
||||
sys_clk = get_board_sys_clk();
|
||||
plat_ratio = (in_be32(&gur->rcwsr[0]) >> 25) & 0x1f;
|
||||
ccb_clk = sys_clk * plat_ratio / 2;
|
||||
|
||||
NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
|
||||
ccb_clk / 16 / CONFIG_BAUDRATE);
|
||||
|
||||
#if defined(CONFIG_SPL_MMC_BOOT)
|
||||
puts("\nSD boot...\n");
|
||||
#elif defined(CONFIG_SPL_SPI_BOOT)
|
||||
puts("\nSPI boot...\n");
|
||||
#elif defined(CONFIG_SPL_NAND_BOOT)
|
||||
puts("\nNAND boot...\n");
|
||||
#endif
|
||||
|
||||
relocate_code(CONFIG_SPL_RELOC_STACK, (gd_t *)CONFIG_SPL_GD_ADDR, 0x0);
|
||||
}
|
||||
|
||||
void board_init_r(gd_t *gd, ulong dest_addr)
|
||||
{
|
||||
bd_t *bd;
|
||||
|
||||
bd = (bd_t *)(gd + sizeof(gd_t));
|
||||
memset(bd, 0, sizeof(bd_t));
|
||||
gd->bd = bd;
|
||||
bd->bi_memstart = CONFIG_SYS_INIT_L3_ADDR;
|
||||
bd->bi_memsize = CONFIG_SYS_L3_SIZE;
|
||||
|
||||
arch_cpu_init();
|
||||
get_clocks();
|
||||
mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR,
|
||||
CONFIG_SPL_RELOC_MALLOC_SIZE);
|
||||
gd->flags |= GD_FLG_FULL_MALLOC_INIT;
|
||||
|
||||
#ifdef CONFIG_SPL_NAND_BOOT
|
||||
nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
|
||||
(uchar *)SPL_ENV_ADDR);
|
||||
#endif
|
||||
#ifdef CONFIG_SPL_MMC_BOOT
|
||||
mmc_initialize(bd);
|
||||
mmc_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
|
||||
(uchar *)SPL_ENV_ADDR);
|
||||
#endif
|
||||
#ifdef CONFIG_SPL_SPI_BOOT
|
||||
fsl_spi_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
|
||||
(uchar *)SPL_ENV_ADDR);
|
||||
#endif
|
||||
|
||||
gd->env_addr = (ulong)(SPL_ENV_ADDR);
|
||||
gd->env_valid = ENV_VALID;
|
||||
|
||||
i2c_init_all();
|
||||
|
||||
dram_init();
|
||||
|
||||
#ifdef CONFIG_SPL_MMC_BOOT
|
||||
mmc_boot();
|
||||
#elif defined(CONFIG_SPL_SPI_BOOT)
|
||||
fsl_spi_boot();
|
||||
#elif defined(CONFIG_SPL_NAND_BOOT)
|
||||
nand_boot();
|
||||
#endif
|
||||
}
|
||||
@@ -1,10 +0,0 @@
|
||||
# single-source clock:Sys_Clock = DDR_Refclock = Diff_Sysclk = 100 MHz
|
||||
# Core/DDR/Platform/FMan = 1400MHz/1600MT/s/400MHz/700MHz
|
||||
|
||||
# PBL preamble and RCW header for T1024QDS
|
||||
aa55aa55 010e0100
|
||||
# Serdes protocol 0x6F
|
||||
0810000e 00000000 00000000 00000000
|
||||
37800001 00000012 e8104000 21000000
|
||||
00000000 00000000 00000000 00030810
|
||||
00000000 036c5a00 00000000 00000006
|
||||
@@ -1,26 +0,0 @@
|
||||
#PBI commands
|
||||
#Initialize CPC1
|
||||
09010000 00200400
|
||||
09138000 00000000
|
||||
091380c0 00000100
|
||||
#Configure CPC1 as 256KB SRAM
|
||||
09010100 00000000
|
||||
09010104 fffc0007
|
||||
09010f00 081e000d
|
||||
09010000 80000000
|
||||
#Configure LAW for CPC1
|
||||
09000cd0 00000000
|
||||
09000cd4 fffc0000
|
||||
09000cd8 81000011
|
||||
#Configure alternate space
|
||||
09000010 00000000
|
||||
09000014 ff000000
|
||||
09000018 81000000
|
||||
#Configure SPI controller
|
||||
09110000 80000403
|
||||
09110020 2d170008
|
||||
09110024 00100008
|
||||
09110028 00100008
|
||||
0911002c 00100008
|
||||
#Flush PBL data
|
||||
091380c0 000FFFFF
|
||||
@@ -1,10 +0,0 @@
|
||||
# single-source clock:Sys_Clock = DDR_Refclock = Diff_Sysclk = 100 MHz
|
||||
# Core/DDR/Platform/FMan = 1400MHz/1600MT/s/400MHz/700MHz
|
||||
|
||||
# PBL preamble and RCW header for T1024QDS
|
||||
aa55aa55 010e0100
|
||||
# Serdes protocol 0x6F
|
||||
0810000e 00000000 00000000 00000000
|
||||
37800001 00000012 68104000 21000000
|
||||
00000000 00000000 00000000 00030810
|
||||
00000000 036c5a00 00000000 00000006
|
||||
@@ -1,10 +0,0 @@
|
||||
# single-source clock:Sys_Clock = DDR_Refclock = Diff_Sysclk = 100 MHz
|
||||
# Core/DDR/Platform/FMan = 1400MHz/1600MT/s/400MHz/700MHz
|
||||
|
||||
# PBL preamble and RCW header for T1024QDS
|
||||
aa55aa55 010e0100
|
||||
# Serdes protocol 0x6F
|
||||
0810000e 00000000 00000000 00000000
|
||||
37800001 00000012 58104000 21000000
|
||||
00000000 00000000 00000000 00030810
|
||||
00000000 036c5a00 00000000 00000006
|
||||
@@ -1,499 +0,0 @@
|
||||
// SPDX-License-Identifier: GPL-2.0+
|
||||
/*
|
||||
* Copyright 2014 Freescale Semiconductor, Inc.
|
||||
* Copyright 2020 NXP
|
||||
*/
|
||||
|
||||
#include <common.h>
|
||||
#include <command.h>
|
||||
#include <env.h>
|
||||
#include <fdt_support.h>
|
||||
#include <i2c.h>
|
||||
#include <image.h>
|
||||
#include <init.h>
|
||||
#include <log.h>
|
||||
#include <netdev.h>
|
||||
#include <linux/compiler.h>
|
||||
#include <asm/mmu.h>
|
||||
#include <asm/processor.h>
|
||||
#include <asm/cache.h>
|
||||
#include <asm/immap_85xx.h>
|
||||
#include <asm/fsl_law.h>
|
||||
#include <asm/fsl_serdes.h>
|
||||
#include <asm/fsl_liodn.h>
|
||||
#include <fm_eth.h>
|
||||
#include <hwconfig.h>
|
||||
#include "../common/qixis.h"
|
||||
#include "t102xqds.h"
|
||||
#include "t102xqds_qixis.h"
|
||||
#include "../common/sleep.h"
|
||||
|
||||
DECLARE_GLOBAL_DATA_PTR;
|
||||
|
||||
int checkboard(void)
|
||||
{
|
||||
char buf[64];
|
||||
struct cpu_type *cpu = gd->arch.cpu;
|
||||
static const char *const freq[] = {"100", "125", "156.25", "100.0"};
|
||||
int clock;
|
||||
u8 sw = QIXIS_READ(arch);
|
||||
|
||||
printf("Board: %sQDS, ", cpu->name);
|
||||
printf("Sys ID: 0x%02x, Board Arch: V%d, ", QIXIS_READ(id), sw >> 4);
|
||||
printf("Board Version: %c, boot from ", (sw & 0xf) + 'A' - 1);
|
||||
|
||||
#ifdef CONFIG_SDCARD
|
||||
puts("SD/MMC\n");
|
||||
#elif CONFIG_SPIFLASH
|
||||
puts("SPI\n");
|
||||
#else
|
||||
sw = QIXIS_READ(brdcfg[0]);
|
||||
sw = (sw & QIXIS_LBMAP_MASK) >> QIXIS_LBMAP_SHIFT;
|
||||
|
||||
if (sw < 0x8)
|
||||
printf("vBank: %d\n", sw);
|
||||
else if (sw == 0x8)
|
||||
puts("PromJet\n");
|
||||
else if (sw == 0x9)
|
||||
puts("NAND\n");
|
||||
else if (sw == 0x15)
|
||||
printf("IFC Card\n");
|
||||
else
|
||||
printf("invalid setting of SW%u\n", QIXIS_LBMAP_SWITCH);
|
||||
#endif
|
||||
|
||||
printf("FPGA: v%d (%s), build %d",
|
||||
(int)QIXIS_READ(scver), qixis_read_tag(buf),
|
||||
(int)qixis_read_minor());
|
||||
/* the timestamp string contains "\n" at the end */
|
||||
printf(" on %s", qixis_read_time(buf));
|
||||
|
||||
puts("SERDES Reference: ");
|
||||
sw = QIXIS_READ(brdcfg[2]);
|
||||
clock = (sw >> 6) & 3;
|
||||
printf("Clock1=%sMHz ", freq[clock]);
|
||||
clock = (sw >> 4) & 3;
|
||||
printf("Clock2=%sMHz\n", freq[clock]);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
int select_i2c_ch_pca9547(u8 ch, int bus_num)
|
||||
{
|
||||
int ret;
|
||||
#ifdef CONFIG_DM_I2C
|
||||
struct udevice *dev;
|
||||
|
||||
ret = i2c_get_chip_for_busnum(bus_num, I2C_MUX_PCA_ADDR_PRI,
|
||||
1, &dev);
|
||||
if (ret) {
|
||||
printf("%s: Cannot find udev for a bus %d\n", __func__,
|
||||
bus_num);
|
||||
return ret;
|
||||
}
|
||||
|
||||
ret = dm_i2c_write(dev, 0, &ch, 1);
|
||||
#else
|
||||
ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1);
|
||||
#endif
|
||||
if (ret) {
|
||||
puts("PCA: failed to select proper channel\n");
|
||||
return ret;
|
||||
}
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static int board_mux_lane_to_slot(void)
|
||||
{
|
||||
ccsr_gur_t __iomem *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
|
||||
u32 srds_prtcl_s1;
|
||||
u8 brdcfg9;
|
||||
|
||||
srds_prtcl_s1 = in_be32(&gur->rcwsr[4]) &
|
||||
FSL_CORENET2_RCWSR4_SRDS1_PRTCL;
|
||||
srds_prtcl_s1 >>= FSL_CORENET2_RCWSR4_SRDS1_PRTCL_SHIFT;
|
||||
|
||||
|
||||
brdcfg9 = QIXIS_READ(brdcfg[9]);
|
||||
QIXIS_WRITE(brdcfg[9], brdcfg9 | BRDCFG9_XFI_TX_DISABLE);
|
||||
|
||||
switch (srds_prtcl_s1) {
|
||||
case 0:
|
||||
/* SerDes1 is not enabled */
|
||||
break;
|
||||
case 0xd5:
|
||||
case 0x5b:
|
||||
case 0x6b:
|
||||
case 0x77:
|
||||
case 0x6f:
|
||||
case 0x7f:
|
||||
QIXIS_WRITE(brdcfg[12], 0x8c);
|
||||
break;
|
||||
case 0x40:
|
||||
QIXIS_WRITE(brdcfg[12], 0xfc);
|
||||
break;
|
||||
case 0xd6:
|
||||
case 0x5a:
|
||||
case 0x6a:
|
||||
case 0x56:
|
||||
QIXIS_WRITE(brdcfg[12], 0x88);
|
||||
break;
|
||||
case 0x47:
|
||||
QIXIS_WRITE(brdcfg[12], 0xcc);
|
||||
break;
|
||||
case 0x46:
|
||||
QIXIS_WRITE(brdcfg[12], 0xc8);
|
||||
break;
|
||||
case 0x95:
|
||||
case 0x99:
|
||||
brdcfg9 &= ~BRDCFG9_XFI_TX_DISABLE;
|
||||
QIXIS_WRITE(brdcfg[9], brdcfg9);
|
||||
QIXIS_WRITE(brdcfg[12], 0x8c);
|
||||
break;
|
||||
case 0x116:
|
||||
QIXIS_WRITE(brdcfg[12], 0x00);
|
||||
break;
|
||||
case 0x115:
|
||||
case 0x119:
|
||||
case 0x129:
|
||||
case 0x12b:
|
||||
/* Aurora, PCIe, SGMII, SATA */
|
||||
QIXIS_WRITE(brdcfg[12], 0x04);
|
||||
break;
|
||||
default:
|
||||
printf("WARNING: unsupported for SerDes Protocol %d\n",
|
||||
srds_prtcl_s1);
|
||||
return -1;
|
||||
}
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
#ifdef CONFIG_ARCH_T1024
|
||||
static void board_mux_setup(void)
|
||||
{
|
||||
u8 brdcfg15;
|
||||
|
||||
brdcfg15 = QIXIS_READ(brdcfg[15]);
|
||||
brdcfg15 &= ~BRDCFG15_DIUSEL_MASK;
|
||||
|
||||
if (hwconfig_arg_cmp("pin_mux", "tdm")) {
|
||||
/* Route QE_TDM multiplexed signals to TDM Riser slot */
|
||||
QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_DIUSEL_TDM);
|
||||
QIXIS_WRITE(brdcfg[13], BRDCFG13_TDM_INTERFACE << 2);
|
||||
QIXIS_WRITE(brdcfg[5], (QIXIS_READ(brdcfg[5]) &
|
||||
~BRDCFG5_SPIRTE_MASK) | BRDCFG5_SPIRTE_TDM);
|
||||
} else if (hwconfig_arg_cmp("pin_mux", "ucc")) {
|
||||
/* to UCC (ProfiBus) interface */
|
||||
QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_DIUSEL_UCC);
|
||||
} else if (hwconfig_arg_cmp("pin_mux", "hdmi")) {
|
||||
/* to DVI (HDMI) encoder */
|
||||
QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_DIUSEL_HDMI);
|
||||
} else if (hwconfig_arg_cmp("pin_mux", "lcd")) {
|
||||
/* to DFP (LCD) encoder */
|
||||
QIXIS_WRITE(brdcfg[15], brdcfg15 | BRDCFG15_LCDFM |
|
||||
BRDCFG15_LCDPD | BRDCFG15_DIUSEL_LCD);
|
||||
}
|
||||
|
||||
if (hwconfig_arg_cmp("adaptor", "sdxc"))
|
||||
/* Route SPI_CS multiplexed signals to SD slot */
|
||||
QIXIS_WRITE(brdcfg[5], (QIXIS_READ(brdcfg[5]) &
|
||||
~BRDCFG5_SPIRTE_MASK) | BRDCFG5_SPIRTE_SDHC);
|
||||
}
|
||||
#endif
|
||||
|
||||
void board_retimer_ds125df111_init(void)
|
||||
{
|
||||
u8 reg;
|
||||
|
||||
#ifdef CONFIG_DM_I2C
|
||||
struct udevice *dev;
|
||||
int ret, bus_num = 0;
|
||||
|
||||
ret = i2c_get_chip_for_busnum(bus_num, I2C_MUX_PCA_ADDR_PRI,
|
||||
1, &dev);
|
||||
if (ret)
|
||||
goto failed;
|
||||
|
||||
/* Retimer DS125DF111 is connected to I2C1_CH7_CH5 */
|
||||
reg = I2C_MUX_CH7;
|
||||
dm_i2c_write(dev, 0, ®, 1);
|
||||
|
||||
ret = i2c_get_chip_for_busnum(bus_num, I2C_MUX_PCA_ADDR_SEC,
|
||||
1, &dev);
|
||||
if (ret)
|
||||
goto failed;
|
||||
|
||||
reg = I2C_MUX_CH5;
|
||||
dm_i2c_write(dev, 0, ®, 1);
|
||||
|
||||
/* Access to Control/Shared register */
|
||||
ret = i2c_get_chip_for_busnum(bus_num, I2C_RETIMER_ADDR,
|
||||
1, &dev);
|
||||
if (ret)
|
||||
goto failed;
|
||||
reg = 0x0;
|
||||
dm_i2c_write(dev, 0xff, ®, 1);
|
||||
|
||||
/* Read device revision and ID */
|
||||
dm_i2c_read(dev, 1, ®, 1);
|
||||
debug("Retimer version id = 0x%x\n", reg);
|
||||
|
||||
/* Enable Broadcast */
|
||||
reg = 0x0c;
|
||||
dm_i2c_write(dev, 0xff, ®, 1);
|
||||
|
||||
/* Reset Channel Registers */
|
||||
dm_i2c_read(dev, 0, ®, 1);
|
||||
reg |= 0x4;
|
||||
dm_i2c_write(dev, 0, ®, 1);
|
||||
|
||||
/* Enable override divider select and Enable Override Output Mux */
|
||||
dm_i2c_read(dev, 9, ®, 1);
|
||||
reg |= 0x24;
|
||||
dm_i2c_write(dev, 9, ®, 1);
|
||||
|
||||
/* Select VCO Divider to full rate (000) */
|
||||
dm_i2c_read(dev, 0x18, ®, 1);
|
||||
reg &= 0x8f;
|
||||
dm_i2c_write(dev, 0x18, ®, 1);
|
||||
|
||||
/* Select active PFD MUX input as re-timed data (001) */
|
||||
dm_i2c_read(dev, 0x1e, ®, 1);
|
||||
reg &= 0x3f;
|
||||
reg |= 0x20;
|
||||
dm_i2c_write(dev, 0x1e, ®, 1);
|
||||
|
||||
/* Set data rate as 10.3125 Gbps */
|
||||
reg = 0x0;
|
||||
dm_i2c_write(dev, 0x60, ®, 1);
|
||||
reg = 0xb2;
|
||||
dm_i2c_write(dev, 0x61, ®, 1);
|
||||
reg = 0x90;
|
||||
dm_i2c_write(dev, 0x62, ®, 1);
|
||||
reg = 0xb3;
|
||||
dm_i2c_write(dev, 0x63, ®, 1);
|
||||
reg = 0xcd;
|
||||
dm_i2c_write(dev, 0x64, ®, 1);
|
||||
return;
|
||||
|
||||
failed:
|
||||
printf("%s: Cannot find udev for a bus %d\n", __func__,
|
||||
bus_num);
|
||||
return;
|
||||
#else
|
||||
/* Retimer DS125DF111 is connected to I2C1_CH7_CH5 */
|
||||
reg = I2C_MUX_CH7;
|
||||
i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, ®, 1);
|
||||
reg = I2C_MUX_CH5;
|
||||
i2c_write(I2C_MUX_PCA_ADDR_SEC, 0, 1, ®, 1);
|
||||
|
||||
/* Access to Control/Shared register */
|
||||
reg = 0x0;
|
||||
i2c_write(I2C_RETIMER_ADDR, 0xff, 1, ®, 1);
|
||||
|
||||
/* Read device revision and ID */
|
||||
i2c_read(I2C_RETIMER_ADDR, 1, 1, ®, 1);
|
||||
debug("Retimer version id = 0x%x\n", reg);
|
||||
|
||||
/* Enable Broadcast */
|
||||
reg = 0x0c;
|
||||
i2c_write(I2C_RETIMER_ADDR, 0xff, 1, ®, 1);
|
||||
|
||||
/* Reset Channel Registers */
|
||||
i2c_read(I2C_RETIMER_ADDR, 0, 1, ®, 1);
|
||||
reg |= 0x4;
|
||||
i2c_write(I2C_RETIMER_ADDR, 0, 1, ®, 1);
|
||||
|
||||
/* Enable override divider select and Enable Override Output Mux */
|
||||
i2c_read(I2C_RETIMER_ADDR, 9, 1, ®, 1);
|
||||
reg |= 0x24;
|
||||
i2c_write(I2C_RETIMER_ADDR, 9, 1, ®, 1);
|
||||
|
||||
/* Select VCO Divider to full rate (000) */
|
||||
i2c_read(I2C_RETIMER_ADDR, 0x18, 1, ®, 1);
|
||||
reg &= 0x8f;
|
||||
i2c_write(I2C_RETIMER_ADDR, 0x18, 1, ®, 1);
|
||||
|
||||
/* Select active PFD MUX input as re-timed data (001) */
|
||||
i2c_read(I2C_RETIMER_ADDR, 0x1e, 1, ®, 1);
|
||||
reg &= 0x3f;
|
||||
reg |= 0x20;
|
||||
i2c_write(I2C_RETIMER_ADDR, 0x1e, 1, ®, 1);
|
||||
|
||||
/* Set data rate as 10.3125 Gbps */
|
||||
reg = 0x0;
|
||||
i2c_write(I2C_RETIMER_ADDR, 0x60, 1, ®, 1);
|
||||
reg = 0xb2;
|
||||
i2c_write(I2C_RETIMER_ADDR, 0x61, 1, ®, 1);
|
||||
reg = 0x90;
|
||||
i2c_write(I2C_RETIMER_ADDR, 0x62, 1, ®, 1);
|
||||
reg = 0xb3;
|
||||
i2c_write(I2C_RETIMER_ADDR, 0x63, 1, ®, 1);
|
||||
reg = 0xcd;
|
||||
i2c_write(I2C_RETIMER_ADDR, 0x64, 1, ®, 1);
|
||||
#endif
|
||||
}
|
||||
|
||||
int board_early_init_f(void)
|
||||
{
|
||||
#if defined(CONFIG_DEEP_SLEEP)
|
||||
if (is_warm_boot())
|
||||
fsl_dp_disable_console();
|
||||
#endif
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
int board_early_init_r(void)
|
||||
{
|
||||
#ifdef CONFIG_SYS_FLASH_BASE
|
||||
const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
|
||||
int flash_esel = find_tlb_idx((void *)flashbase, 1);
|
||||
|
||||
/*
|
||||
* Remap Boot flash + PROMJET region to caching-inhibited
|
||||
* so that flash can be erased properly.
|
||||
*/
|
||||
|
||||
/* Flush d-cache and invalidate i-cache of any FLASH data */
|
||||
flush_dcache();
|
||||
invalidate_icache();
|
||||
|
||||
if (flash_esel == -1) {
|
||||
/* very unlikely unless something is messed up */
|
||||
puts("Error: Could not find TLB for FLASH BASE\n");
|
||||
flash_esel = 2; /* give our best effort to continue */
|
||||
} else {
|
||||
/* invalidate existing TLB entry for flash + promjet */
|
||||
disable_tlb(flash_esel);
|
||||
}
|
||||
|
||||
set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
||||
0, flash_esel, BOOKE_PAGESZ_256M, 1);
|
||||
#endif
|
||||
select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT, 0);
|
||||
board_mux_lane_to_slot();
|
||||
board_retimer_ds125df111_init();
|
||||
|
||||
/* Increase IO drive strength to address FCS error on RGMII */
|
||||
out_be32((unsigned *)CONFIG_SYS_FSL_SCFG_IODSECR1_ADDR, 0xbfdb7800);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
unsigned long get_board_sys_clk(void)
|
||||
{
|
||||
u8 sysclk_conf = QIXIS_READ(brdcfg[1]);
|
||||
|
||||
switch (sysclk_conf & 0x0F) {
|
||||
case QIXIS_SYSCLK_64:
|
||||
return 64000000;
|
||||
case QIXIS_SYSCLK_83:
|
||||
return 83333333;
|
||||
case QIXIS_SYSCLK_100:
|
||||
return 100000000;
|
||||
case QIXIS_SYSCLK_125:
|
||||
return 125000000;
|
||||
case QIXIS_SYSCLK_133:
|
||||
return 133333333;
|
||||
case QIXIS_SYSCLK_150:
|
||||
return 150000000;
|
||||
case QIXIS_SYSCLK_160:
|
||||
return 160000000;
|
||||
case QIXIS_SYSCLK_166:
|
||||
return 166666666;
|
||||
}
|
||||
return 66666666;
|
||||
}
|
||||
|
||||
unsigned long get_board_ddr_clk(void)
|
||||
{
|
||||
u8 ddrclk_conf = QIXIS_READ(brdcfg[1]);
|
||||
|
||||
switch ((ddrclk_conf & 0x30) >> 4) {
|
||||
case QIXIS_DDRCLK_100:
|
||||
return 100000000;
|
||||
case QIXIS_DDRCLK_125:
|
||||
return 125000000;
|
||||
case QIXIS_DDRCLK_133:
|
||||
return 133333333;
|
||||
}
|
||||
return 66666666;
|
||||
}
|
||||
|
||||
#define NUM_SRDS_PLL 2
|
||||
int misc_init_r(void)
|
||||
{
|
||||
#ifdef CONFIG_ARCH_T1024
|
||||
board_mux_setup();
|
||||
#endif
|
||||
return 0;
|
||||
}
|
||||
|
||||
void fdt_fixup_spi_mux(void *blob)
|
||||
{
|
||||
int nodeoff = 0;
|
||||
|
||||
if (hwconfig_arg_cmp("pin_mux", "tdm")) {
|
||||
while ((nodeoff = fdt_node_offset_by_compatible(blob, 0,
|
||||
"eon,en25s64")) >= 0) {
|
||||
fdt_del_node(blob, nodeoff);
|
||||
}
|
||||
} else {
|
||||
/* remove tdm node */
|
||||
while ((nodeoff = fdt_node_offset_by_compatible(blob, 0,
|
||||
"maxim,ds26522")) >= 0) {
|
||||
fdt_del_node(blob, nodeoff);
|
||||
}
|
||||
}
|
||||
}
|
||||
|
||||
int ft_board_setup(void *blob, bd_t *bd)
|
||||
{
|
||||
phys_addr_t base;
|
||||
phys_size_t size;
|
||||
|
||||
ft_cpu_setup(blob, bd);
|
||||
|
||||
base = env_get_bootm_low();
|
||||
size = env_get_bootm_size();
|
||||
|
||||
fdt_fixup_memory(blob, (u64)base, (u64)size);
|
||||
|
||||
#ifdef CONFIG_PCI
|
||||
pci_of_setup(blob, bd);
|
||||
#endif
|
||||
|
||||
fdt_fixup_liodn(blob);
|
||||
|
||||
#ifdef CONFIG_HAS_FSL_DR_USB
|
||||
fsl_fdt_fixup_dr_usb(blob, bd);
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_SYS_DPAA_FMAN
|
||||
#ifndef CONFIG_DM_ETH
|
||||
fdt_fixup_fman_ethernet(blob);
|
||||
#endif
|
||||
fdt_fixup_board_enet(blob);
|
||||
#endif
|
||||
fdt_fixup_spi_mux(blob);
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
void qixis_dump_switch(void)
|
||||
{
|
||||
int i, nr_of_cfgsw;
|
||||
|
||||
QIXIS_WRITE(cms[0], 0x00);
|
||||
nr_of_cfgsw = QIXIS_READ(cms[1]);
|
||||
|
||||
puts("DIP switch settings dump:\n");
|
||||
for (i = 1; i <= nr_of_cfgsw; i++) {
|
||||
QIXIS_WRITE(cms[0], i);
|
||||
printf("SW%d = (0x%02x)\n", i, QIXIS_READ(cms[1]));
|
||||
}
|
||||
}
|
||||
@@ -1,14 +0,0 @@
|
||||
/* SPDX-License-Identifier: GPL-2.0+ */
|
||||
/*
|
||||
* Copyright 2014 Freescale Semiconductor, Inc.
|
||||
* Copyright 2020 NXP
|
||||
*/
|
||||
|
||||
#ifndef __T102x_QDS_H__
|
||||
#define __T102x_QDS_H__
|
||||
|
||||
void fdt_fixup_board_enet(void *blob);
|
||||
void pci_of_setup(void *blob, bd_t *bd);
|
||||
int select_i2c_ch_pca9547(u8 ch, int bus_num);
|
||||
|
||||
#endif
|
||||
@@ -1,63 +0,0 @@
|
||||
/* SPDX-License-Identifier: GPL-2.0+ */
|
||||
/*
|
||||
* Copyright 2014 Freescale Semiconductor, Inc.
|
||||
*/
|
||||
|
||||
#ifndef __T1024QDS_QIXIS_H__
|
||||
#define __T1024QDS_QIXIS_H__
|
||||
|
||||
/* Definitions of QIXIS Registers for T1024/T1023 QDS */
|
||||
|
||||
/* BRDCFG4[4:7]] select EC1 and EC2 as a pair */
|
||||
#define BRDCFG4_EMISEL_MASK 0xE0
|
||||
#define BRDCFG4_EMISEL_SHIFT 5
|
||||
|
||||
/* BRDCFG5[0:1] controls routing and use of I2C3 & I2C4 ports*/
|
||||
#define BRDCFG5_IMX_MASK 0xC0
|
||||
#define BRDCFG5_IMX_DIU 0x80
|
||||
|
||||
#define BRDCFG5_SPIRTE_MASK 0x07
|
||||
#define BRDCFG5_SPIRTE_TDM 0x01
|
||||
#define BRDCFG5_SPIRTE_SDHC 0x02
|
||||
#define BRDCFG9_XFI_TX_DISABLE 0x10
|
||||
|
||||
/* BRDCFG13[0:5] TDM configuration and setup */
|
||||
#define BRDCFG13_TDM_MASK 0xfc
|
||||
#define BRDCFG13_TDM_INTERFACE 0x37
|
||||
#define BRDCFG13_HDLC_LOOPBACK 0x29
|
||||
#define BRDCFG13_TDM_LOOPBACK 0x31
|
||||
|
||||
/* BRDCFG15[3] controls LCD Panel Powerdown */
|
||||
#define BRDCFG15_LCDFM 0x20
|
||||
#define BRDCFG15_LCDPD 0x10
|
||||
#define BRDCFG15_LCDPD_MASK 0x10
|
||||
#define BRDCFG15_LCDPD_ENABLED 0x00
|
||||
|
||||
/* BRDCFG15[6:7] controls DIU MUX selction*/
|
||||
#define BRDCFG15_DIUSEL_MASK 0x03
|
||||
#define BRDCFG15_DIUSEL_HDMI 0x00
|
||||
#define BRDCFG15_DIUSEL_LCD 0x01
|
||||
#define BRDCFG15_DIUSEL_UCC 0x02
|
||||
#define BRDCFG15_DIUSEL_TDM 0x03
|
||||
|
||||
/* SYSCLK */
|
||||
#define QIXIS_SYSCLK_66 0x0
|
||||
#define QIXIS_SYSCLK_83 0x1
|
||||
#define QIXIS_SYSCLK_100 0x2
|
||||
#define QIXIS_SYSCLK_125 0x3
|
||||
#define QIXIS_SYSCLK_133 0x4
|
||||
#define QIXIS_SYSCLK_150 0x5
|
||||
#define QIXIS_SYSCLK_160 0x6
|
||||
#define QIXIS_SYSCLK_166 0x7
|
||||
#define QIXIS_SYSCLK_64 0x8
|
||||
|
||||
/* DDRCLK */
|
||||
#define QIXIS_DDRCLK_66 0x0
|
||||
#define QIXIS_DDRCLK_100 0x1
|
||||
#define QIXIS_DDRCLK_125 0x2
|
||||
#define QIXIS_DDRCLK_133 0x3
|
||||
|
||||
|
||||
#define QIXIS_SRDS1CLK_122 0x5a
|
||||
#define QIXIS_SRDS1CLK_125 0x5e
|
||||
#endif
|
||||
@@ -1,116 +0,0 @@
|
||||
// SPDX-License-Identifier: GPL-2.0+
|
||||
/*
|
||||
* Copyright 2014 Freescale Semiconductor, Inc.
|
||||
*/
|
||||
|
||||
#include <common.h>
|
||||
#include <asm/mmu.h>
|
||||
|
||||
struct fsl_e_tlb_entry tlb_table[] = {
|
||||
/* TLB 0 - for temp stack in cache */
|
||||
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
|
||||
CONFIG_SYS_INIT_RAM_ADDR_PHYS,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, 0,
|
||||
0, 0, BOOKE_PAGESZ_4K, 0),
|
||||
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
|
||||
CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, 0,
|
||||
0, 0, BOOKE_PAGESZ_4K, 0),
|
||||
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
|
||||
CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, 0,
|
||||
0, 0, BOOKE_PAGESZ_4K, 0),
|
||||
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
|
||||
CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, 0,
|
||||
0, 0, BOOKE_PAGESZ_4K, 0),
|
||||
|
||||
/* TLB 1 */
|
||||
/* *I*** - Covers boot page */
|
||||
#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR)
|
||||
/*
|
||||
* *I*G - L3SRAM. When L3 is used as 256K SRAM, the address of the
|
||||
* SRAM is at 0xfffc0000, it covered the 0xfffff000.
|
||||
*/
|
||||
SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
||||
0, 0, BOOKE_PAGESZ_256K, 1),
|
||||
#else
|
||||
SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
||||
0, 0, BOOKE_PAGESZ_4K, 1),
|
||||
#endif
|
||||
|
||||
/* *I*G* - CCSRBAR */
|
||||
SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
||||
0, 1, BOOKE_PAGESZ_16M, 1),
|
||||
|
||||
/* *I*G* - Flash, localbus */
|
||||
/* This will be changed to *I*G* after relocation to RAM. */
|
||||
SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
|
||||
MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
|
||||
0, 2, BOOKE_PAGESZ_256M, 1),
|
||||
|
||||
#ifndef CONFIG_SPL_BUILD
|
||||
/* *I*G* - PCI */
|
||||
SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
||||
0, 3, BOOKE_PAGESZ_1G, 1),
|
||||
|
||||
/* *I*G* - PCI I/O */
|
||||
SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
||||
0, 4, BOOKE_PAGESZ_256K, 1),
|
||||
|
||||
/* Bman/Qman */
|
||||
#ifdef CONFIG_SYS_BMAN_MEM_PHYS
|
||||
SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, 0,
|
||||
0, 5, BOOKE_PAGESZ_16M, 1),
|
||||
SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000,
|
||||
CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
||||
0, 6, BOOKE_PAGESZ_16M, 1),
|
||||
#endif
|
||||
#ifdef CONFIG_SYS_QMAN_MEM_PHYS
|
||||
SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, 0,
|
||||
0, 7, BOOKE_PAGESZ_16M, 1),
|
||||
SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000,
|
||||
CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
||||
0, 8, BOOKE_PAGESZ_16M, 1),
|
||||
#endif
|
||||
#endif
|
||||
#ifdef CONFIG_SYS_DCSRBAR_PHYS
|
||||
SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
||||
0, 9, BOOKE_PAGESZ_4M, 1),
|
||||
#endif
|
||||
#ifdef CONFIG_SYS_NAND_BASE
|
||||
SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
||||
0, 10, BOOKE_PAGESZ_64K, 1),
|
||||
#endif
|
||||
#ifdef QIXIS_BASE
|
||||
SET_TLB_ENTRY(1, QIXIS_BASE, QIXIS_BASE_PHYS,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
||||
0, 11, BOOKE_PAGESZ_4K, 1),
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SPL_BUILD)
|
||||
SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M,
|
||||
0, 12, BOOKE_PAGESZ_1G, 1),
|
||||
SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
|
||||
CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
|
||||
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_M,
|
||||
0, 13, BOOKE_PAGESZ_1G, 1)
|
||||
#endif
|
||||
/* entry 14 and 15 has been used hard coded, they will be disabled
|
||||
* in cpu_init_f, so if needed more, will use entry 16 later.
|
||||
*/
|
||||
};
|
||||
|
||||
int num_tlb_entries = ARRAY_SIZE(tlb_table);
|
||||
@@ -1,69 +0,0 @@
|
||||
CONFIG_PPC=y
|
||||
CONFIG_SYS_TEXT_BASE=0xEFF40000
|
||||
CONFIG_ENV_SIZE=0x2000
|
||||
CONFIG_NXP_ESBC=y
|
||||
CONFIG_MPC85xx=y
|
||||
CONFIG_TARGET_T1024QDS=y
|
||||
# CONFIG_SYS_MALLOC_F is not set
|
||||
CONFIG_FIT=y
|
||||
CONFIG_FIT_VERBOSE=y
|
||||
CONFIG_OF_BOARD_SETUP=y
|
||||
CONFIG_OF_STDOUT_VIA_ALIAS=y
|
||||
CONFIG_BOOTDELAY=10
|
||||
CONFIG_SILENT_CONSOLE=y
|
||||
# CONFIG_CONSOLE_MUX is not set
|
||||
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
|
||||
CONFIG_BOARD_EARLY_INIT_F=y
|
||||
CONFIG_BOARD_EARLY_INIT_R=y
|
||||
CONFIG_HUSH_PARSER=y
|
||||
CONFIG_CMD_IMLS=y
|
||||
CONFIG_CMD_GREPENV=y
|
||||
CONFIG_CMD_I2C=y
|
||||
CONFIG_CMD_MMC=y
|
||||
CONFIG_CMD_SF=y
|
||||
CONFIG_CMD_USB=y
|
||||
CONFIG_CMD_DHCP=y
|
||||
CONFIG_CMD_MII=y
|
||||
CONFIG_CMD_PING=y
|
||||
CONFIG_CMD_BMP=y
|
||||
CONFIG_CMD_DATE=y
|
||||
CONFIG_MP=y
|
||||
CONFIG_CMD_EXT2=y
|
||||
CONFIG_CMD_FAT=y
|
||||
CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.0"
|
||||
CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:2m(uboot),9m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:2m(uboot),9m(kernel),128k(dtb),-(user)"
|
||||
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
|
||||
CONFIG_DM=y
|
||||
CONFIG_FSL_ESDHC=y
|
||||
CONFIG_MTD=y
|
||||
CONFIG_MTD_NOR_FLASH=y
|
||||
CONFIG_FLASH_CFI_DRIVER=y
|
||||
CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
|
||||
CONFIG_FLASH_CFI_MTD=y
|
||||
CONFIG_SYS_FLASH_CFI=y
|
||||
CONFIG_SPI_FLASH=y
|
||||
CONFIG_SF_DEFAULT_MODE=0
|
||||
CONFIG_SF_DEFAULT_SPEED=10000000
|
||||
CONFIG_SPI_FLASH_EON=y
|
||||
CONFIG_SPI_FLASH_STMICRO=y
|
||||
CONFIG_SPI_FLASH_SST=y
|
||||
CONFIG_PHYLIB=y
|
||||
CONFIG_PHYLIB_10G=y
|
||||
CONFIG_PHY_REALTEK=y
|
||||
CONFIG_PHY_TERANETICS=y
|
||||
CONFIG_PHY_VITESSE=y
|
||||
CONFIG_PHY_GIGE=y
|
||||
CONFIG_E1000=y
|
||||
CONFIG_FMAN_ENET=y
|
||||
CONFIG_MII=y
|
||||
CONFIG_SYS_QE_FMAN_FW_IN_NOR=y
|
||||
CONFIG_SYS_NS16550=y
|
||||
CONFIG_SPI=y
|
||||
CONFIG_FSL_ESPI=y
|
||||
CONFIG_USB=y
|
||||
CONFIG_USB_STORAGE=y
|
||||
CONFIG_VIDEO=y
|
||||
CONFIG_RSA=y
|
||||
CONFIG_SPL_RSA=y
|
||||
CONFIG_RSA_SOFTWARE_EXP=y
|
||||
CONFIG_OF_LIBFDT=y
|
||||
@@ -1,64 +0,0 @@
|
||||
CONFIG_PPC=y
|
||||
CONFIG_SYS_TEXT_BASE=0xEFF40000
|
||||
CONFIG_ENV_SIZE=0x2000
|
||||
CONFIG_ENV_SECT_SIZE=0x20000
|
||||
CONFIG_MPC85xx=y
|
||||
CONFIG_TARGET_T1024QDS=y
|
||||
CONFIG_FIT=y
|
||||
CONFIG_FIT_VERBOSE=y
|
||||
CONFIG_OF_BOARD_SETUP=y
|
||||
CONFIG_OF_STDOUT_VIA_ALIAS=y
|
||||
CONFIG_BOOTDELAY=10
|
||||
CONFIG_SILENT_CONSOLE=y
|
||||
# CONFIG_CONSOLE_MUX is not set
|
||||
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
|
||||
CONFIG_BOARD_EARLY_INIT_F=y
|
||||
CONFIG_BOARD_EARLY_INIT_R=y
|
||||
CONFIG_HUSH_PARSER=y
|
||||
CONFIG_CMD_IMLS=y
|
||||
CONFIG_CMD_GREPENV=y
|
||||
CONFIG_CMD_I2C=y
|
||||
CONFIG_CMD_MMC=y
|
||||
CONFIG_CMD_SF=y
|
||||
CONFIG_CMD_USB=y
|
||||
CONFIG_CMD_DHCP=y
|
||||
CONFIG_CMD_MII=y
|
||||
CONFIG_CMD_PING=y
|
||||
CONFIG_CMD_BMP=y
|
||||
CONFIG_CMD_DATE=y
|
||||
CONFIG_MP=y
|
||||
CONFIG_CMD_EXT2=y
|
||||
CONFIG_CMD_FAT=y
|
||||
CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.0"
|
||||
CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:2m(uboot),9m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:2m(uboot),9m(kernel),128k(dtb),-(user)"
|
||||
CONFIG_ENV_IS_IN_FLASH=y
|
||||
CONFIG_ENV_ADDR=0xEFF20000
|
||||
CONFIG_FSL_CAAM=y
|
||||
CONFIG_FSL_ESDHC=y
|
||||
CONFIG_MTD=y
|
||||
CONFIG_MTD_NOR_FLASH=y
|
||||
CONFIG_FLASH_CFI_DRIVER=y
|
||||
CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
|
||||
CONFIG_FLASH_CFI_MTD=y
|
||||
CONFIG_SYS_FLASH_CFI=y
|
||||
CONFIG_SPI_FLASH=y
|
||||
CONFIG_SF_DEFAULT_MODE=0
|
||||
CONFIG_SF_DEFAULT_SPEED=10000000
|
||||
CONFIG_SPI_FLASH_EON=y
|
||||
CONFIG_SPI_FLASH_STMICRO=y
|
||||
CONFIG_SPI_FLASH_SST=y
|
||||
CONFIG_PHYLIB=y
|
||||
CONFIG_PHYLIB_10G=y
|
||||
CONFIG_PHY_REALTEK=y
|
||||
CONFIG_PHY_TERANETICS=y
|
||||
CONFIG_PHY_VITESSE=y
|
||||
CONFIG_FMAN_ENET=y
|
||||
CONFIG_MII=y
|
||||
CONFIG_SYS_QE_FMAN_FW_IN_NOR=y
|
||||
CONFIG_SYS_NS16550=y
|
||||
CONFIG_SPI=y
|
||||
CONFIG_FSL_ESPI=y
|
||||
CONFIG_USB=y
|
||||
CONFIG_USB_STORAGE=y
|
||||
CONFIG_VIDEO=y
|
||||
CONFIG_OF_LIBFDT=y
|
||||
@@ -1,83 +0,0 @@
|
||||
CONFIG_PPC=y
|
||||
CONFIG_SYS_TEXT_BASE=0x00201000
|
||||
CONFIG_SPL_LIBCOMMON_SUPPORT=y
|
||||
CONFIG_SPL_LIBGENERIC_SUPPORT=y
|
||||
CONFIG_ENV_SIZE=0x2000
|
||||
CONFIG_ENV_OFFSET=0x140000
|
||||
CONFIG_SPL_SERIAL_SUPPORT=y
|
||||
CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
|
||||
CONFIG_SPL=y
|
||||
CONFIG_SPL_TEXT_BASE=0xFFFD8000
|
||||
CONFIG_MPC85xx=y
|
||||
CONFIG_TARGET_T1024QDS=y
|
||||
CONFIG_SYS_CUSTOM_LDSCRIPT=y
|
||||
CONFIG_SYS_LDSCRIPT="arch/powerpc/cpu/mpc85xx/u-boot-nand.lds"
|
||||
CONFIG_FIT=y
|
||||
CONFIG_FIT_VERBOSE=y
|
||||
CONFIG_OF_BOARD_SETUP=y
|
||||
CONFIG_OF_STDOUT_VIA_ALIAS=y
|
||||
CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL"
|
||||
CONFIG_BOOTDELAY=10
|
||||
CONFIG_SILENT_CONSOLE=y
|
||||
# CONFIG_CONSOLE_MUX is not set
|
||||
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
|
||||
CONFIG_BOARD_EARLY_INIT_F=y
|
||||
CONFIG_BOARD_EARLY_INIT_R=y
|
||||
# CONFIG_SPL_FRAMEWORK is not set
|
||||
CONFIG_SPL_NAND_BOOT=y
|
||||
CONFIG_SPL_FSL_PBL=y
|
||||
CONFIG_SPL_ENV_SUPPORT=y
|
||||
CONFIG_SPL_I2C_SUPPORT=y
|
||||
CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y
|
||||
CONFIG_SPL_NAND_SUPPORT=y
|
||||
CONFIG_HUSH_PARSER=y
|
||||
CONFIG_CMD_IMLS=y
|
||||
CONFIG_CMD_GREPENV=y
|
||||
CONFIG_CMD_I2C=y
|
||||
CONFIG_CMD_MMC=y
|
||||
CONFIG_CMD_SF=y
|
||||
CONFIG_CMD_USB=y
|
||||
CONFIG_CMD_DHCP=y
|
||||
CONFIG_CMD_MII=y
|
||||
CONFIG_CMD_PING=y
|
||||
CONFIG_CMD_BMP=y
|
||||
CONFIG_CMD_DATE=y
|
||||
CONFIG_MP=y
|
||||
CONFIG_CMD_EXT2=y
|
||||
CONFIG_CMD_FAT=y
|
||||
CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.0"
|
||||
CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:2m(uboot),9m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:2m(uboot),9m(kernel),128k(dtb),-(user)"
|
||||
CONFIG_ENV_IS_IN_NAND=y
|
||||
CONFIG_FSL_CAAM=y
|
||||
CONFIG_SYS_FSL_DDR3=y
|
||||
CONFIG_FSL_ESDHC=y
|
||||
CONFIG_MTD=y
|
||||
CONFIG_MTD_NOR_FLASH=y
|
||||
CONFIG_FLASH_CFI_DRIVER=y
|
||||
CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
|
||||
CONFIG_FLASH_CFI_MTD=y
|
||||
CONFIG_SYS_FLASH_CFI=y
|
||||
CONFIG_MTD_RAW_NAND=y
|
||||
CONFIG_SPI_FLASH=y
|
||||
CONFIG_SF_DEFAULT_MODE=0
|
||||
CONFIG_SF_DEFAULT_SPEED=10000000
|
||||
CONFIG_SPI_FLASH_EON=y
|
||||
CONFIG_SPI_FLASH_STMICRO=y
|
||||
CONFIG_SPI_FLASH_SST=y
|
||||
CONFIG_PHYLIB=y
|
||||
CONFIG_PHYLIB_10G=y
|
||||
CONFIG_PHY_REALTEK=y
|
||||
CONFIG_PHY_TERANETICS=y
|
||||
CONFIG_PHY_VITESSE=y
|
||||
CONFIG_PHY_GIGE=y
|
||||
CONFIG_E1000=y
|
||||
CONFIG_FMAN_ENET=y
|
||||
CONFIG_MII=y
|
||||
CONFIG_SYS_QE_FMAN_FW_IN_NAND=y
|
||||
CONFIG_SYS_NS16550=y
|
||||
CONFIG_SPI=y
|
||||
CONFIG_FSL_ESPI=y
|
||||
CONFIG_USB=y
|
||||
CONFIG_USB_STORAGE=y
|
||||
CONFIG_VIDEO=y
|
||||
CONFIG_OF_LIBFDT=y
|
||||
@@ -1,80 +0,0 @@
|
||||
CONFIG_PPC=y
|
||||
CONFIG_SYS_TEXT_BASE=0x00201000
|
||||
CONFIG_SPL_LIBCOMMON_SUPPORT=y
|
||||
CONFIG_SPL_LIBGENERIC_SUPPORT=y
|
||||
CONFIG_ENV_SIZE=0x2000
|
||||
CONFIG_ENV_OFFSET=0x100000
|
||||
CONFIG_SPL_MMC_SUPPORT=y
|
||||
CONFIG_SPL_SERIAL_SUPPORT=y
|
||||
CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
|
||||
CONFIG_SPL=y
|
||||
CONFIG_SPL_TEXT_BASE=0xFFFD8000
|
||||
CONFIG_MPC85xx=y
|
||||
CONFIG_TARGET_T1024QDS=y
|
||||
CONFIG_FIT=y
|
||||
CONFIG_FIT_VERBOSE=y
|
||||
CONFIG_OF_BOARD_SETUP=y
|
||||
CONFIG_OF_STDOUT_VIA_ALIAS=y
|
||||
CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SDCARD"
|
||||
CONFIG_BOOTDELAY=10
|
||||
CONFIG_SILENT_CONSOLE=y
|
||||
# CONFIG_CONSOLE_MUX is not set
|
||||
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
|
||||
CONFIG_BOARD_EARLY_INIT_F=y
|
||||
CONFIG_BOARD_EARLY_INIT_R=y
|
||||
# CONFIG_SPL_FRAMEWORK is not set
|
||||
CONFIG_SPL_MMC_BOOT=y
|
||||
CONFIG_SPL_FSL_PBL=y
|
||||
CONFIG_SPL_ENV_SUPPORT=y
|
||||
CONFIG_SPL_I2C_SUPPORT=y
|
||||
CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y
|
||||
CONFIG_HUSH_PARSER=y
|
||||
CONFIG_CMD_IMLS=y
|
||||
CONFIG_CMD_GREPENV=y
|
||||
CONFIG_CMD_I2C=y
|
||||
CONFIG_CMD_MMC=y
|
||||
CONFIG_CMD_SF=y
|
||||
CONFIG_CMD_USB=y
|
||||
CONFIG_CMD_DHCP=y
|
||||
CONFIG_CMD_MII=y
|
||||
CONFIG_CMD_PING=y
|
||||
CONFIG_CMD_BMP=y
|
||||
CONFIG_CMD_DATE=y
|
||||
CONFIG_MP=y
|
||||
CONFIG_CMD_EXT2=y
|
||||
CONFIG_CMD_FAT=y
|
||||
CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.0"
|
||||
CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:2m(uboot),9m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:2m(uboot),9m(kernel),128k(dtb),-(user)"
|
||||
CONFIG_ENV_IS_IN_MMC=y
|
||||
CONFIG_FSL_CAAM=y
|
||||
CONFIG_SYS_FSL_DDR3=y
|
||||
CONFIG_FSL_ESDHC=y
|
||||
CONFIG_MTD=y
|
||||
CONFIG_MTD_NOR_FLASH=y
|
||||
CONFIG_FLASH_CFI_DRIVER=y
|
||||
CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
|
||||
CONFIG_FLASH_CFI_MTD=y
|
||||
CONFIG_SYS_FLASH_CFI=y
|
||||
CONFIG_SPI_FLASH=y
|
||||
CONFIG_SF_DEFAULT_MODE=0
|
||||
CONFIG_SF_DEFAULT_SPEED=10000000
|
||||
CONFIG_SPI_FLASH_EON=y
|
||||
CONFIG_SPI_FLASH_STMICRO=y
|
||||
CONFIG_SPI_FLASH_SST=y
|
||||
CONFIG_PHYLIB=y
|
||||
CONFIG_PHYLIB_10G=y
|
||||
CONFIG_PHY_REALTEK=y
|
||||
CONFIG_PHY_TERANETICS=y
|
||||
CONFIG_PHY_VITESSE=y
|
||||
CONFIG_PHY_GIGE=y
|
||||
CONFIG_E1000=y
|
||||
CONFIG_FMAN_ENET=y
|
||||
CONFIG_MII=y
|
||||
CONFIG_SYS_QE_FMAN_FW_IN_MMC=y
|
||||
CONFIG_SYS_NS16550=y
|
||||
CONFIG_SPI=y
|
||||
CONFIG_FSL_ESPI=y
|
||||
CONFIG_USB=y
|
||||
CONFIG_USB_STORAGE=y
|
||||
CONFIG_VIDEO=y
|
||||
CONFIG_OF_LIBFDT=y
|
||||
@@ -1,70 +0,0 @@
|
||||
CONFIG_PPC=y
|
||||
CONFIG_SYS_TEXT_BASE=0xEFF40000
|
||||
CONFIG_ENV_SIZE=0x2000
|
||||
CONFIG_NXP_ESBC=y
|
||||
CONFIG_MPC85xx=y
|
||||
CONFIG_TARGET_T1024QDS=y
|
||||
# CONFIG_SYS_MALLOC_F is not set
|
||||
CONFIG_FIT=y
|
||||
CONFIG_FIT_VERBOSE=y
|
||||
CONFIG_OF_BOARD_SETUP=y
|
||||
CONFIG_OF_STDOUT_VIA_ALIAS=y
|
||||
CONFIG_BOOTDELAY=10
|
||||
CONFIG_SILENT_CONSOLE=y
|
||||
# CONFIG_CONSOLE_MUX is not set
|
||||
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
|
||||
CONFIG_BOARD_EARLY_INIT_F=y
|
||||
CONFIG_BOARD_EARLY_INIT_R=y
|
||||
CONFIG_HUSH_PARSER=y
|
||||
CONFIG_CMD_IMLS=y
|
||||
CONFIG_CMD_GREPENV=y
|
||||
CONFIG_CMD_I2C=y
|
||||
CONFIG_CMD_MMC=y
|
||||
CONFIG_CMD_SF=y
|
||||
CONFIG_CMD_USB=y
|
||||
CONFIG_CMD_DHCP=y
|
||||
CONFIG_CMD_MII=y
|
||||
CONFIG_CMD_PING=y
|
||||
CONFIG_CMD_BMP=y
|
||||
CONFIG_CMD_DATE=y
|
||||
CONFIG_MP=y
|
||||
CONFIG_CMD_EXT2=y
|
||||
CONFIG_CMD_FAT=y
|
||||
CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.0"
|
||||
CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:2m(uboot),9m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:2m(uboot),9m(kernel),128k(dtb),-(user)"
|
||||
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
|
||||
CONFIG_DM=y
|
||||
CONFIG_SYS_FSL_DDR3=y
|
||||
CONFIG_FSL_ESDHC=y
|
||||
CONFIG_MTD=y
|
||||
CONFIG_MTD_NOR_FLASH=y
|
||||
CONFIG_FLASH_CFI_DRIVER=y
|
||||
CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
|
||||
CONFIG_FLASH_CFI_MTD=y
|
||||
CONFIG_SYS_FLASH_CFI=y
|
||||
CONFIG_SPI_FLASH=y
|
||||
CONFIG_SF_DEFAULT_MODE=0
|
||||
CONFIG_SF_DEFAULT_SPEED=10000000
|
||||
CONFIG_SPI_FLASH_EON=y
|
||||
CONFIG_SPI_FLASH_STMICRO=y
|
||||
CONFIG_SPI_FLASH_SST=y
|
||||
CONFIG_PHYLIB=y
|
||||
CONFIG_PHYLIB_10G=y
|
||||
CONFIG_PHY_REALTEK=y
|
||||
CONFIG_PHY_TERANETICS=y
|
||||
CONFIG_PHY_VITESSE=y
|
||||
CONFIG_PHY_GIGE=y
|
||||
CONFIG_E1000=y
|
||||
CONFIG_FMAN_ENET=y
|
||||
CONFIG_MII=y
|
||||
CONFIG_SYS_QE_FMAN_FW_IN_NOR=y
|
||||
CONFIG_SYS_NS16550=y
|
||||
CONFIG_SPI=y
|
||||
CONFIG_FSL_ESPI=y
|
||||
CONFIG_USB=y
|
||||
CONFIG_USB_STORAGE=y
|
||||
CONFIG_VIDEO=y
|
||||
CONFIG_RSA=y
|
||||
CONFIG_SPL_RSA=y
|
||||
CONFIG_RSA_SOFTWARE_EXP=y
|
||||
CONFIG_OF_LIBFDT=y
|
||||
@@ -1,83 +0,0 @@
|
||||
CONFIG_PPC=y
|
||||
CONFIG_SYS_TEXT_BASE=0x00201000
|
||||
CONFIG_SPL_LIBCOMMON_SUPPORT=y
|
||||
CONFIG_SPL_LIBGENERIC_SUPPORT=y
|
||||
CONFIG_ENV_SIZE=0x2000
|
||||
CONFIG_ENV_OFFSET=0x100000
|
||||
CONFIG_ENV_SECT_SIZE=0x10000
|
||||
CONFIG_SPL_SERIAL_SUPPORT=y
|
||||
CONFIG_SPL_DRIVERS_MISC_SUPPORT=y
|
||||
CONFIG_SPL=y
|
||||
CONFIG_SPL_SPI_FLASH_SUPPORT=y
|
||||
CONFIG_SPL_SPI_SUPPORT=y
|
||||
CONFIG_SPL_TEXT_BASE=0xFFFD8000
|
||||
CONFIG_MPC85xx=y
|
||||
CONFIG_TARGET_T1024QDS=y
|
||||
CONFIG_FIT=y
|
||||
CONFIG_FIT_VERBOSE=y
|
||||
CONFIG_OF_BOARD_SETUP=y
|
||||
CONFIG_OF_STDOUT_VIA_ALIAS=y
|
||||
CONFIG_SYS_EXTRA_OPTIONS="RAMBOOT_PBL,SPIFLASH"
|
||||
CONFIG_BOOTDELAY=10
|
||||
CONFIG_SILENT_CONSOLE=y
|
||||
# CONFIG_CONSOLE_MUX is not set
|
||||
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
|
||||
CONFIG_BOARD_EARLY_INIT_F=y
|
||||
CONFIG_BOARD_EARLY_INIT_R=y
|
||||
# CONFIG_SPL_FRAMEWORK is not set
|
||||
CONFIG_SPL_SPI_BOOT=y
|
||||
CONFIG_SPL_FSL_PBL=y
|
||||
CONFIG_SPL_ENV_SUPPORT=y
|
||||
CONFIG_SPL_I2C_SUPPORT=y
|
||||
CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT=y
|
||||
CONFIG_HUSH_PARSER=y
|
||||
CONFIG_CMD_IMLS=y
|
||||
CONFIG_CMD_GREPENV=y
|
||||
CONFIG_CMD_I2C=y
|
||||
CONFIG_CMD_MMC=y
|
||||
CONFIG_CMD_SF=y
|
||||
CONFIG_CMD_USB=y
|
||||
CONFIG_CMD_DHCP=y
|
||||
CONFIG_CMD_MII=y
|
||||
CONFIG_CMD_PING=y
|
||||
CONFIG_CMD_BMP=y
|
||||
CONFIG_CMD_DATE=y
|
||||
CONFIG_MP=y
|
||||
CONFIG_CMD_EXT2=y
|
||||
CONFIG_CMD_FAT=y
|
||||
CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.0"
|
||||
CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:2m(uboot),9m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:2m(uboot),9m(kernel),128k(dtb),-(user)"
|
||||
CONFIG_ENV_IS_IN_SPI_FLASH=y
|
||||
CONFIG_ENV_ADDR=0xFFFC9000
|
||||
CONFIG_FSL_CAAM=y
|
||||
CONFIG_SYS_FSL_DDR3=y
|
||||
CONFIG_FSL_ESDHC=y
|
||||
CONFIG_MTD=y
|
||||
CONFIG_MTD_NOR_FLASH=y
|
||||
CONFIG_FLASH_CFI_DRIVER=y
|
||||
CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
|
||||
CONFIG_FLASH_CFI_MTD=y
|
||||
CONFIG_SYS_FLASH_CFI=y
|
||||
CONFIG_SPI_FLASH=y
|
||||
CONFIG_SF_DEFAULT_MODE=0
|
||||
CONFIG_SF_DEFAULT_SPEED=10000000
|
||||
CONFIG_SPI_FLASH_EON=y
|
||||
CONFIG_SPI_FLASH_STMICRO=y
|
||||
CONFIG_SPI_FLASH_SST=y
|
||||
CONFIG_PHYLIB=y
|
||||
CONFIG_PHYLIB_10G=y
|
||||
CONFIG_PHY_REALTEK=y
|
||||
CONFIG_PHY_TERANETICS=y
|
||||
CONFIG_PHY_VITESSE=y
|
||||
CONFIG_PHY_GIGE=y
|
||||
CONFIG_E1000=y
|
||||
CONFIG_FMAN_ENET=y
|
||||
CONFIG_MII=y
|
||||
CONFIG_SYS_QE_FMAN_FW_IN_SPIFLASH=y
|
||||
CONFIG_SYS_NS16550=y
|
||||
CONFIG_SPI=y
|
||||
CONFIG_FSL_ESPI=y
|
||||
CONFIG_USB=y
|
||||
CONFIG_USB_STORAGE=y
|
||||
CONFIG_VIDEO=y
|
||||
CONFIG_OF_LIBFDT=y
|
||||
@@ -1,67 +0,0 @@
|
||||
CONFIG_PPC=y
|
||||
CONFIG_SYS_TEXT_BASE=0xEFF40000
|
||||
CONFIG_ENV_SIZE=0x2000
|
||||
CONFIG_ENV_SECT_SIZE=0x20000
|
||||
CONFIG_MPC85xx=y
|
||||
CONFIG_TARGET_T1024QDS=y
|
||||
CONFIG_FIT=y
|
||||
CONFIG_FIT_VERBOSE=y
|
||||
CONFIG_OF_BOARD_SETUP=y
|
||||
CONFIG_OF_STDOUT_VIA_ALIAS=y
|
||||
CONFIG_BOOTDELAY=10
|
||||
CONFIG_SILENT_CONSOLE=y
|
||||
# CONFIG_CONSOLE_MUX is not set
|
||||
CONFIG_SYS_CONSOLE_IS_IN_ENV=y
|
||||
CONFIG_BOARD_EARLY_INIT_F=y
|
||||
CONFIG_BOARD_EARLY_INIT_R=y
|
||||
CONFIG_HUSH_PARSER=y
|
||||
CONFIG_CMD_IMLS=y
|
||||
CONFIG_CMD_GREPENV=y
|
||||
CONFIG_CMD_I2C=y
|
||||
CONFIG_CMD_MMC=y
|
||||
CONFIG_CMD_SF=y
|
||||
CONFIG_CMD_USB=y
|
||||
CONFIG_CMD_DHCP=y
|
||||
CONFIG_CMD_MII=y
|
||||
CONFIG_CMD_PING=y
|
||||
CONFIG_CMD_BMP=y
|
||||
CONFIG_CMD_DATE=y
|
||||
CONFIG_MP=y
|
||||
CONFIG_CMD_EXT2=y
|
||||
CONFIG_CMD_FAT=y
|
||||
CONFIG_MTDIDS_DEFAULT="nor0=fe8000000.nor,nand0=fff800000.flash,spi0=spife110000.0"
|
||||
CONFIG_MTDPARTS_DEFAULT="mtdparts=fe8000000.nor:1m(uboot),5m(kernel),128k(dtb),96m(fs),-(user);fff800000.flash:2m(uboot),9m(kernel),128k(dtb),96m(fs),-(user);spife110000.0:2m(uboot),9m(kernel),128k(dtb),-(user)"
|
||||
CONFIG_ENV_IS_IN_FLASH=y
|
||||
CONFIG_ENV_ADDR=0xEFF20000
|
||||
CONFIG_FSL_CAAM=y
|
||||
CONFIG_SYS_FSL_DDR3=y
|
||||
CONFIG_FSL_ESDHC=y
|
||||
CONFIG_MTD=y
|
||||
CONFIG_MTD_NOR_FLASH=y
|
||||
CONFIG_FLASH_CFI_DRIVER=y
|
||||
CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
|
||||
CONFIG_FLASH_CFI_MTD=y
|
||||
CONFIG_SYS_FLASH_CFI=y
|
||||
CONFIG_SPI_FLASH=y
|
||||
CONFIG_SF_DEFAULT_MODE=0
|
||||
CONFIG_SF_DEFAULT_SPEED=10000000
|
||||
CONFIG_SPI_FLASH_EON=y
|
||||
CONFIG_SPI_FLASH_STMICRO=y
|
||||
CONFIG_SPI_FLASH_SST=y
|
||||
CONFIG_PHYLIB=y
|
||||
CONFIG_PHYLIB_10G=y
|
||||
CONFIG_PHY_REALTEK=y
|
||||
CONFIG_PHY_TERANETICS=y
|
||||
CONFIG_PHY_VITESSE=y
|
||||
CONFIG_PHY_GIGE=y
|
||||
CONFIG_E1000=y
|
||||
CONFIG_FMAN_ENET=y
|
||||
CONFIG_MII=y
|
||||
CONFIG_SYS_QE_FMAN_FW_IN_NOR=y
|
||||
CONFIG_SYS_NS16550=y
|
||||
CONFIG_SPI=y
|
||||
CONFIG_FSL_ESPI=y
|
||||
CONFIG_USB=y
|
||||
CONFIG_USB_STORAGE=y
|
||||
CONFIG_VIDEO=y
|
||||
CONFIG_OF_LIBFDT=y
|
||||
@@ -1,756 +0,0 @@
|
||||
/* SPDX-License-Identifier: GPL-2.0+ */
|
||||
/*
|
||||
* Copyright 2014 Freescale Semiconductor, Inc.
|
||||
* Copyright 2020 NXP
|
||||
*/
|
||||
|
||||
/*
|
||||
* T1024/T1023 QDS board configuration file
|
||||
*/
|
||||
|
||||
#ifndef __T1024QDS_H
|
||||
#define __T1024QDS_H
|
||||
|
||||
#include <linux/stringify.h>
|
||||
|
||||
/* High Level Configuration Options */
|
||||
#define CONFIG_SYS_BOOK3E_HV /* Category E.HV supported */
|
||||
#define CONFIG_ENABLE_36BIT_PHYS
|
||||
|
||||
#ifdef CONFIG_PHYS_64BIT
|
||||
#define CONFIG_ADDR_MAP 1
|
||||
#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
|
||||
#endif
|
||||
|
||||
#define CONFIG_SYS_FSL_CPC /* Corenet Platform Cache */
|
||||
#define CONFIG_SYS_NUM_CPC CONFIG_SYS_NUM_DDR_CTLRS
|
||||
|
||||
#define CONFIG_ENV_OVERWRITE
|
||||
|
||||
#define CONFIG_DEEP_SLEEP
|
||||
|
||||
#ifdef CONFIG_RAMBOOT_PBL
|
||||
#define CONFIG_SYS_FSL_PBL_PBI board/freescale/t102xqds/t1024_pbi.cfg
|
||||
#define CONFIG_SPL_FLUSH_IMAGE
|
||||
#define CONFIG_SPL_PAD_TO 0x40000
|
||||
#define CONFIG_SPL_MAX_SIZE 0x28000
|
||||
#define RESET_VECTOR_OFFSET 0x27FFC
|
||||
#define BOOT_PAGE_OFFSET 0x27000
|
||||
#ifdef CONFIG_SPL_BUILD
|
||||
#define CONFIG_SPL_SKIP_RELOCATE
|
||||
#define CONFIG_SPL_COMMON_INIT_DDR
|
||||
#define CONFIG_SYS_CCSR_DO_NOT_RELOCATE
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_MTD_RAW_NAND
|
||||
#define CONFIG_SYS_NAND_U_BOOT_SIZE (768 << 10)
|
||||
#define CONFIG_SYS_NAND_U_BOOT_DST 0x00200000
|
||||
#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000
|
||||
#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10)
|
||||
#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xqds/t1024_nand_rcw.cfg
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_SPIFLASH
|
||||
#define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC
|
||||
#define CONFIG_SPL_SPI_FLASH_MINIMAL
|
||||
#define CONFIG_SYS_SPI_FLASH_U_BOOT_SIZE (768 << 10)
|
||||
#define CONFIG_SYS_SPI_FLASH_U_BOOT_DST (0x00200000)
|
||||
#define CONFIG_SYS_SPI_FLASH_U_BOOT_START (0x00200000)
|
||||
#define CONFIG_SYS_SPI_FLASH_U_BOOT_OFFS (256 << 10)
|
||||
#ifndef CONFIG_SPL_BUILD
|
||||
#define CONFIG_SYS_MPC85XX_NO_RESETVEC
|
||||
#endif
|
||||
#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xqds/t1024_spi_rcw.cfg
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_SDCARD
|
||||
#define CONFIG_RESET_VECTOR_ADDRESS 0x200FFC
|
||||
#define CONFIG_SYS_MMC_U_BOOT_SIZE (768 << 10)
|
||||
#define CONFIG_SYS_MMC_U_BOOT_DST (0x00200000)
|
||||
#define CONFIG_SYS_MMC_U_BOOT_START (0x00200000)
|
||||
#define CONFIG_SYS_MMC_U_BOOT_OFFS (260 << 10)
|
||||
#ifndef CONFIG_SPL_BUILD
|
||||
#define CONFIG_SYS_MPC85XX_NO_RESETVEC
|
||||
#endif
|
||||
#define CONFIG_SYS_FSL_PBL_RCW board/freescale/t102xqds/t1024_sd_rcw.cfg
|
||||
#endif
|
||||
|
||||
#endif /* CONFIG_RAMBOOT_PBL */
|
||||
|
||||
#ifndef CONFIG_RESET_VECTOR_ADDRESS
|
||||
#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc
|
||||
#endif
|
||||
|
||||
/* PCIe Boot - Master */
|
||||
#define CONFIG_SRIO_PCIE_BOOT_MASTER
|
||||
/*
|
||||
* for slave u-boot IMAGE instored in master memory space,
|
||||
* PHYS must be aligned based on the SIZE
|
||||
*/
|
||||
#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff00000ull
|
||||
#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE 0x100000 /* 1M */
|
||||
#ifdef CONFIG_PHYS_64BIT
|
||||
#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef200000ull
|
||||
#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff00000ull
|
||||
#else
|
||||
#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xef200000
|
||||
#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0xfff00000
|
||||
#endif
|
||||
/*
|
||||
* for slave UCODE and ENV instored in master memory space,
|
||||
* PHYS must be aligned based on the SIZE
|
||||
*/
|
||||
#ifdef CONFIG_PHYS_64BIT
|
||||
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef100000ull
|
||||
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
|
||||
#else
|
||||
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xef100000
|
||||
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0xffe00000
|
||||
#endif
|
||||
#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE 0x40000 /* 256K */
|
||||
/* slave core release by master*/
|
||||
#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
|
||||
#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
|
||||
|
||||
/* PCIe Boot - Slave */
|
||||
#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
|
||||
#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
|
||||
#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
|
||||
(0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
|
||||
/* Set 1M boot space for PCIe boot */
|
||||
#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
|
||||
#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
|
||||
(0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
|
||||
#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_SPIFLASH)
|
||||
#elif defined(CONFIG_SDCARD)
|
||||
#define CONFIG_SYS_MMC_ENV_DEV 0
|
||||
#endif
|
||||
|
||||
#ifndef __ASSEMBLY__
|
||||
unsigned long get_board_sys_clk(void);
|
||||
unsigned long get_board_ddr_clk(void);
|
||||
#endif
|
||||
|
||||
#define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
|
||||
#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk()
|
||||
|
||||
/*
|
||||
* These can be toggled for performance analysis, otherwise use default.
|
||||
*/
|
||||
#define CONFIG_SYS_CACHE_STASHING
|
||||
#define CONFIG_BACKSIDE_L2_CACHE
|
||||
#define CONFIG_SYS_INIT_L2CSR0 L2CSR0_L2E
|
||||
#define CONFIG_BTB /* toggle branch predition */
|
||||
#define CONFIG_DDR_ECC
|
||||
#ifdef CONFIG_DDR_ECC
|
||||
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
|
||||
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
|
||||
#endif
|
||||
|
||||
/*
|
||||
* Config the L3 Cache as L3 SRAM
|
||||
*/
|
||||
#define CONFIG_SYS_INIT_L3_ADDR 0xFFFC0000
|
||||
#define CONFIG_SYS_L3_SIZE (256 << 10)
|
||||
#define CONFIG_SPL_GD_ADDR (CONFIG_SYS_INIT_L3_ADDR + 32 * 1024)
|
||||
#define SPL_ENV_ADDR (CONFIG_SPL_GD_ADDR + 4 * 1024)
|
||||
#define CONFIG_SPL_RELOC_MALLOC_ADDR (CONFIG_SPL_GD_ADDR + 12 * 1024)
|
||||
#define CONFIG_SPL_RELOC_MALLOC_SIZE (30 << 10)
|
||||
#define CONFIG_SPL_RELOC_STACK (CONFIG_SPL_GD_ADDR + 64 * 1024)
|
||||
|
||||
#ifdef CONFIG_PHYS_64BIT
|
||||
#define CONFIG_SYS_DCSRBAR 0xf0000000
|
||||
#define CONFIG_SYS_DCSRBAR_PHYS 0xf00000000ull
|
||||
#endif
|
||||
|
||||
/* EEPROM */
|
||||
#define CONFIG_ID_EEPROM
|
||||
#define CONFIG_SYS_I2C_EEPROM_NXID
|
||||
#define CONFIG_SYS_EEPROM_BUS_NUM 0
|
||||
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
|
||||
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
|
||||
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
|
||||
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
|
||||
|
||||
/*
|
||||
* DDR Setup
|
||||
*/
|
||||
#define CONFIG_VERY_BIG_RAM
|
||||
#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
|
||||
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
|
||||
#define CONFIG_DIMM_SLOTS_PER_CTLR 1
|
||||
#define CONFIG_CHIP_SELECTS_PER_CTRL (4 * CONFIG_DIMM_SLOTS_PER_CTLR)
|
||||
#define CONFIG_DDR_SPD
|
||||
|
||||
#define CONFIG_SYS_SPD_BUS_NUM 0
|
||||
#define SPD_EEPROM_ADDRESS 0x51
|
||||
|
||||
#define CONFIG_SYS_SDRAM_SIZE 4096 /* for fixed parameter use */
|
||||
|
||||
/*
|
||||
* IFC Definitions
|
||||
*/
|
||||
#define CONFIG_SYS_FLASH_BASE 0xe0000000
|
||||
#ifdef CONFIG_PHYS_64BIT
|
||||
#define CONFIG_SYS_FLASH_BASE_PHYS (0xf00000000ull | CONFIG_SYS_FLASH_BASE)
|
||||
#else
|
||||
#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
|
||||
#endif
|
||||
|
||||
#define CONFIG_SYS_NOR0_CSPR_EXT (0xf)
|
||||
#define CONFIG_SYS_NOR0_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
|
||||
+ 0x8000000) | \
|
||||
CSPR_PORT_SIZE_16 | \
|
||||
CSPR_MSEL_NOR | \
|
||||
CSPR_V)
|
||||
#define CONFIG_SYS_NOR1_CSPR_EXT (0xf)
|
||||
#define CONFIG_SYS_NOR1_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
|
||||
CSPR_PORT_SIZE_16 | \
|
||||
CSPR_MSEL_NOR | \
|
||||
CSPR_V)
|
||||
#define CONFIG_SYS_NOR_AMASK IFC_AMASK(128*1024*1024)
|
||||
/* NOR Flash Timing Params */
|
||||
#define CONFIG_SYS_NOR_CSOR CSOR_NAND_TRHZ_80
|
||||
#define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x4) | \
|
||||
FTIM0_NOR_TEADC(0x5) | \
|
||||
FTIM0_NOR_TEAHC(0x5))
|
||||
#define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \
|
||||
FTIM1_NOR_TRAD_NOR(0x1A) |\
|
||||
FTIM1_NOR_TSEQRAD_NOR(0x13))
|
||||
#define CONFIG_SYS_NOR_FTIM2 (FTIM2_NOR_TCS(0x4) | \
|
||||
FTIM2_NOR_TCH(0x4) | \
|
||||
FTIM2_NOR_TWPH(0x0E) | \
|
||||
FTIM2_NOR_TWP(0x1c))
|
||||
#define CONFIG_SYS_NOR_FTIM3 0x0
|
||||
|
||||
#define CONFIG_SYS_FLASH_QUIET_TEST
|
||||
#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */
|
||||
|
||||
#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
|
||||
#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
|
||||
#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
|
||||
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
|
||||
|
||||
#define CONFIG_SYS_FLASH_EMPTY_INFO
|
||||
#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS \
|
||||
+ 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
|
||||
#define CONFIG_FSL_QIXIS /* use common QIXIS code */
|
||||
#define QIXIS_BASE 0xffdf0000
|
||||
#ifdef CONFIG_PHYS_64BIT
|
||||
#define QIXIS_BASE_PHYS (0xf00000000ull | QIXIS_BASE)
|
||||
#else
|
||||
#define QIXIS_BASE_PHYS QIXIS_BASE
|
||||
#endif
|
||||
#define QIXIS_LBMAP_SWITCH 0x06
|
||||
#define QIXIS_LBMAP_MASK 0x0f
|
||||
#define QIXIS_LBMAP_SHIFT 0
|
||||
#define QIXIS_LBMAP_DFLTBANK 0x00
|
||||
#define QIXIS_LBMAP_ALTBANK 0x04
|
||||
#define QIXIS_RST_CTL_RESET 0x31
|
||||
#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
|
||||
#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
|
||||
#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
|
||||
#define QIXIS_RST_FORCE_MEM 0x01
|
||||
|
||||
#define CONFIG_SYS_CSPR3_EXT (0xf)
|
||||
#define CONFIG_SYS_CSPR3 (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
|
||||
| CSPR_PORT_SIZE_8 \
|
||||
| CSPR_MSEL_GPCM \
|
||||
| CSPR_V)
|
||||
#define CONFIG_SYS_AMASK3 IFC_AMASK(64 * 1024)
|
||||
#define CONFIG_SYS_CSOR3 0x0
|
||||
/* QIXIS Timing parameters for IFC CS3 */
|
||||
#define CONFIG_SYS_CS3_FTIM0 (FTIM0_GPCM_TACSE(0x0e) | \
|
||||
FTIM0_GPCM_TEADC(0x0e) | \
|
||||
FTIM0_GPCM_TEAHC(0x0e))
|
||||
#define CONFIG_SYS_CS3_FTIM1 (FTIM1_GPCM_TACO(0xff) | \
|
||||
FTIM1_GPCM_TRAD(0x3f))
|
||||
#define CONFIG_SYS_CS3_FTIM2 (FTIM2_GPCM_TCS(0x0e) | \
|
||||
FTIM2_GPCM_TCH(0x8) | \
|
||||
FTIM2_GPCM_TWP(0x1f))
|
||||
#define CONFIG_SYS_CS3_FTIM3 0x0
|
||||
|
||||
#define CONFIG_NAND_FSL_IFC
|
||||
#define CONFIG_SYS_NAND_BASE 0xff800000
|
||||
#ifdef CONFIG_PHYS_64BIT
|
||||
#define CONFIG_SYS_NAND_BASE_PHYS (0xf00000000ull | CONFIG_SYS_NAND_BASE)
|
||||
#else
|
||||
#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
|
||||
#endif
|
||||
#define CONFIG_SYS_NAND_CSPR_EXT (0xf)
|
||||
#define CONFIG_SYS_NAND_CSPR (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
|
||||
| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
|
||||
| CSPR_MSEL_NAND /* MSEL = NAND */ \
|
||||
| CSPR_V)
|
||||
#define CONFIG_SYS_NAND_AMASK IFC_AMASK(64*1024)
|
||||
|
||||
#define CONFIG_SYS_NAND_CSOR (CSOR_NAND_ECC_ENC_EN /* ECC on encode */ \
|
||||
| CSOR_NAND_ECC_DEC_EN /* ECC on decode */ \
|
||||
| CSOR_NAND_ECC_MODE_4 /* 4-bit ECC */ \
|
||||
| CSOR_NAND_RAL_3 /* RAL = 3Byes */ \
|
||||
| CSOR_NAND_PGS_2K /* Page Size = 2K */ \
|
||||
| CSOR_NAND_SPRZ_64/* Spare size = 64 */ \
|
||||
| CSOR_NAND_PB(64)) /*Pages Per Block = 64*/
|
||||
|
||||
#define CONFIG_SYS_NAND_ONFI_DETECTION
|
||||
|
||||
/* ONFI NAND Flash mode0 Timing Params */
|
||||
#define CONFIG_SYS_NAND_FTIM0 (FTIM0_NAND_TCCST(0x07) | \
|
||||
FTIM0_NAND_TWP(0x18) | \
|
||||
FTIM0_NAND_TWCHT(0x07) | \
|
||||
FTIM0_NAND_TWH(0x0a))
|
||||
#define CONFIG_SYS_NAND_FTIM1 (FTIM1_NAND_TADLE(0x32) | \
|
||||
FTIM1_NAND_TWBE(0x39) | \
|
||||
FTIM1_NAND_TRR(0x0e) | \
|
||||
FTIM1_NAND_TRP(0x18))
|
||||
#define CONFIG_SYS_NAND_FTIM2 (FTIM2_NAND_TRAD(0x0f) | \
|
||||
FTIM2_NAND_TREH(0x0a) | \
|
||||
FTIM2_NAND_TWHRE(0x1e))
|
||||
#define CONFIG_SYS_NAND_FTIM3 0x0
|
||||
|
||||
#define CONFIG_SYS_NAND_DDR_LAW 11
|
||||
#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE }
|
||||
#define CONFIG_SYS_MAX_NAND_DEVICE 1
|
||||
|
||||
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
|
||||
|
||||
#if defined(CONFIG_MTD_RAW_NAND)
|
||||
#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NAND_CSPR_EXT
|
||||
#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR
|
||||
#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK
|
||||
#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR
|
||||
#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0
|
||||
#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1
|
||||
#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2
|
||||
#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3
|
||||
#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR0_CSPR_EXT
|
||||
#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR0_CSPR
|
||||
#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
|
||||
#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
|
||||
#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
|
||||
#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
|
||||
#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
|
||||
#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
|
||||
#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NOR1_CSPR_EXT
|
||||
#define CONFIG_SYS_CSPR2 CONFIG_SYS_NOR1_CSPR
|
||||
#define CONFIG_SYS_AMASK2 CONFIG_SYS_NOR_AMASK
|
||||
#define CONFIG_SYS_CSOR2 CONFIG_SYS_NOR_CSOR
|
||||
#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NOR_FTIM0
|
||||
#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NOR_FTIM1
|
||||
#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NOR_FTIM2
|
||||
#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NOR_FTIM3
|
||||
#else
|
||||
#define CONFIG_SYS_CSPR0_EXT CONFIG_SYS_NOR0_CSPR_EXT
|
||||
#define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR0_CSPR
|
||||
#define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK
|
||||
#define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR
|
||||
#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NOR_FTIM0
|
||||
#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NOR_FTIM1
|
||||
#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NOR_FTIM2
|
||||
#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NOR_FTIM3
|
||||
#define CONFIG_SYS_CSPR1_EXT CONFIG_SYS_NOR1_CSPR_EXT
|
||||
#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR1_CSPR
|
||||
#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK
|
||||
#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR
|
||||
#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0
|
||||
#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1
|
||||
#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2
|
||||
#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3
|
||||
#define CONFIG_SYS_CSPR2_EXT CONFIG_SYS_NAND_CSPR_EXT
|
||||
#define CONFIG_SYS_CSPR2 CONFIG_SYS_NAND_CSPR
|
||||
#define CONFIG_SYS_AMASK2 CONFIG_SYS_NAND_AMASK
|
||||
#define CONFIG_SYS_CSOR2 CONFIG_SYS_NAND_CSOR
|
||||
#define CONFIG_SYS_CS2_FTIM0 CONFIG_SYS_NAND_FTIM0
|
||||
#define CONFIG_SYS_CS2_FTIM1 CONFIG_SYS_NAND_FTIM1
|
||||
#define CONFIG_SYS_CS2_FTIM2 CONFIG_SYS_NAND_FTIM2
|
||||
#define CONFIG_SYS_CS2_FTIM3 CONFIG_SYS_NAND_FTIM3
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_SPL_BUILD
|
||||
#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE
|
||||
#else
|
||||
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
|
||||
#endif
|
||||
|
||||
#if defined(CONFIG_RAMBOOT_PBL)
|
||||
#define CONFIG_SYS_RAMBOOT
|
||||
#endif
|
||||
|
||||
#define CONFIG_HWCONFIG
|
||||
|
||||
/* define to use L1 as initial stack */
|
||||
#define CONFIG_L1_INIT_RAM
|
||||
#define CONFIG_SYS_INIT_RAM_LOCK
|
||||
#define CONFIG_SYS_INIT_RAM_ADDR 0xfdd00000 /* Initial L1 address */
|
||||
#ifdef CONFIG_PHYS_64BIT
|
||||
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0xf
|
||||
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW 0xfe03c000
|
||||
/* The assembler doesn't like typecast */
|
||||
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
|
||||
((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
|
||||
CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
|
||||
#else
|
||||
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS 0xfe03c000 /* Initial L1 address */
|
||||
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0
|
||||
#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS
|
||||
#endif
|
||||
#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000
|
||||
|
||||
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
|
||||
GENERATED_GBL_DATA_SIZE)
|
||||
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
||||
|
||||
#define CONFIG_SYS_MONITOR_LEN (768 * 1024)
|
||||
#define CONFIG_SYS_MALLOC_LEN (10 * 1024 * 1024)
|
||||
|
||||
/* Serial Port */
|
||||
#define CONFIG_SYS_NS16550_SERIAL
|
||||
#define CONFIG_SYS_NS16550_REG_SIZE 1
|
||||
#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
|
||||
|
||||
#define CONFIG_SYS_BAUDRATE_TABLE \
|
||||
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
|
||||
|
||||
#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
|
||||
#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
|
||||
#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
|
||||
#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
|
||||
|
||||
/* Video */
|
||||
#ifdef CONFIG_ARCH_T1024 /* no DIU on T1023 */
|
||||
#define CONFIG_FSL_DIU_FB
|
||||
#ifdef CONFIG_FSL_DIU_FB
|
||||
#define CONFIG_FSL_DIU_CH7301
|
||||
#define CONFIG_SYS_DIU_ADDR (CONFIG_SYS_CCSRBAR + 0x180000)
|
||||
#define CONFIG_VIDEO_LOGO
|
||||
#define CONFIG_VIDEO_BMP_LOGO
|
||||
#define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS
|
||||
/*
|
||||
* With CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS, flash I/O is really slow, so
|
||||
* disable empty flash sector detection, which is I/O-intensive.
|
||||
*/
|
||||
#undef CONFIG_SYS_FLASH_EMPTY_INFO
|
||||
#endif
|
||||
#endif
|
||||
|
||||
/* I2C */
|
||||
#ifndef CONFIG_DM_I2C
|
||||
#define CONFIG_SYS_I2C
|
||||
#define CONFIG_SYS_FSL_I2C_SPEED 50000 /* I2C speed in Hz */
|
||||
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
|
||||
#define CONFIG_SYS_FSL_I2C2_SPEED 50000 /* I2C speed in Hz */
|
||||
#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
|
||||
#define CONFIG_SYS_FSL_I2C_OFFSET 0x118000
|
||||
#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
|
||||
#else
|
||||
#define CONFIG_I2C_SET_DEFAULT_BUS_NUM
|
||||
#define CONFIG_I2C_DEFAULT_BUS_NUMBER 0
|
||||
#endif
|
||||
|
||||
#define CONFIG_SYS_I2C_FSL /* Use FSL common I2C driver */
|
||||
|
||||
#define I2C_MUX_PCA_ADDR 0x77
|
||||
#define I2C_MUX_PCA_ADDR_PRI 0x77 /* Primary Mux*/
|
||||
#define I2C_MUX_PCA_ADDR_SEC 0x76 /* Secondary multiplexer */
|
||||
#define I2C_RETIMER_ADDR 0x18
|
||||
|
||||
/* I2C bus multiplexer */
|
||||
#define I2C_MUX_CH_DEFAULT 0x8
|
||||
#define I2C_MUX_CH_DIU 0xC
|
||||
#define I2C_MUX_CH5 0xD
|
||||
#define I2C_MUX_CH7 0xF
|
||||
|
||||
/* LDI/DVI Encoder for display */
|
||||
#define CONFIG_SYS_I2C_LDI_ADDR 0x38
|
||||
#define CONFIG_SYS_I2C_DVI_ADDR 0x75
|
||||
#define CONFIG_SYS_I2C_DVI_BUS_NUM 0
|
||||
|
||||
/*
|
||||
* RTC configuration
|
||||
*/
|
||||
#define RTC
|
||||
#define CONFIG_RTC_DS3231 1
|
||||
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
|
||||
|
||||
/*
|
||||
* eSPI - Enhanced SPI
|
||||
*/
|
||||
|
||||
/*
|
||||
* General PCIe
|
||||
* Memory space is mapped 1-1, but I/O space must start from 0.
|
||||
*/
|
||||
#define CONFIG_PCIE1 /* PCIE controller 1 */
|
||||
#define CONFIG_PCIE2 /* PCIE controller 2 */
|
||||
#define CONFIG_PCIE3 /* PCIE controller 3 */
|
||||
#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */
|
||||
#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */
|
||||
#define CONFIG_PCI_INDIRECT_BRIDGE
|
||||
|
||||
#ifdef CONFIG_PCI
|
||||
/* controller 1, direct to uli, tgtid 3, Base address 20000 */
|
||||
#ifdef CONFIG_PCIE1
|
||||
#define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000
|
||||
#ifdef CONFIG_PHYS_64BIT
|
||||
#define CONFIG_SYS_PCIE1_MEM_BUS 0xe0000000
|
||||
#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc00000000ull
|
||||
#else
|
||||
#define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000
|
||||
#define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000
|
||||
#endif
|
||||
#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000 /* 256M */
|
||||
#define CONFIG_SYS_PCIE1_IO_VIRT 0xf8000000
|
||||
#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
|
||||
#ifdef CONFIG_PHYS_64BIT
|
||||
#define CONFIG_SYS_PCIE1_IO_PHYS 0xff8000000ull
|
||||
#else
|
||||
#define CONFIG_SYS_PCIE1_IO_PHYS 0xf8000000
|
||||
#endif
|
||||
#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
|
||||
#endif
|
||||
|
||||
/* controller 2, Slot 2, tgtid 2, Base address 201000 */
|
||||
#ifdef CONFIG_PCIE2
|
||||
#define CONFIG_SYS_PCIE2_MEM_VIRT 0x90000000
|
||||
#ifdef CONFIG_PHYS_64BIT
|
||||
#define CONFIG_SYS_PCIE2_MEM_BUS 0xe0000000
|
||||
#define CONFIG_SYS_PCIE2_MEM_PHYS 0xc10000000ull
|
||||
#else
|
||||
#define CONFIG_SYS_PCIE2_MEM_BUS 0x90000000
|
||||
#define CONFIG_SYS_PCIE2_MEM_PHYS 0x90000000
|
||||
#endif
|
||||
#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */
|
||||
#define CONFIG_SYS_PCIE2_IO_VIRT 0xf8010000
|
||||
#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
|
||||
#ifdef CONFIG_PHYS_64BIT
|
||||
#define CONFIG_SYS_PCIE2_IO_PHYS 0xff8010000ull
|
||||
#else
|
||||
#define CONFIG_SYS_PCIE2_IO_PHYS 0xf8010000
|
||||
#endif
|
||||
#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
|
||||
#endif
|
||||
|
||||
/* controller 3, Slot 1, tgtid 1, Base address 202000 */
|
||||
#ifdef CONFIG_PCIE3
|
||||
#define CONFIG_SYS_PCIE3_MEM_VIRT 0xa0000000
|
||||
#ifdef CONFIG_PHYS_64BIT
|
||||
#define CONFIG_SYS_PCIE3_MEM_BUS 0xe0000000
|
||||
#define CONFIG_SYS_PCIE3_MEM_PHYS 0xc20000000ull
|
||||
#else
|
||||
#define CONFIG_SYS_PCIE3_MEM_BUS 0xa0000000
|
||||
#define CONFIG_SYS_PCIE3_MEM_PHYS 0xa0000000
|
||||
#endif
|
||||
#define CONFIG_SYS_PCIE3_MEM_SIZE 0x10000000 /* 256M */
|
||||
#define CONFIG_SYS_PCIE3_IO_VIRT 0xf8020000
|
||||
#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000
|
||||
#ifdef CONFIG_PHYS_64BIT
|
||||
#define CONFIG_SYS_PCIE3_IO_PHYS 0xff8020000ull
|
||||
#else
|
||||
#define CONFIG_SYS_PCIE3_IO_PHYS 0xf8020000
|
||||
#endif
|
||||
#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */
|
||||
#endif
|
||||
|
||||
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
|
||||
#endif /* CONFIG_PCI */
|
||||
|
||||
/*
|
||||
*SATA
|
||||
*/
|
||||
#define CONFIG_FSL_SATA_V2
|
||||
#ifdef CONFIG_FSL_SATA_V2
|
||||
#define CONFIG_SYS_SATA_MAX_DEVICE 1
|
||||
#define CONFIG_SATA1
|
||||
#define CONFIG_SYS_SATA1 CONFIG_SYS_MPC85xx_SATA1_ADDR
|
||||
#define CONFIG_SYS_SATA1_FLAGS FLAGS_DMA
|
||||
#define CONFIG_LBA48
|
||||
#endif
|
||||
|
||||
/*
|
||||
* USB
|
||||
*/
|
||||
#define CONFIG_HAS_FSL_DR_USB
|
||||
|
||||
#ifdef CONFIG_HAS_FSL_DR_USB
|
||||
#define CONFIG_USB_EHCI_FSL
|
||||
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
|
||||
#endif
|
||||
|
||||
/*
|
||||
* SDHC
|
||||
*/
|
||||
#ifdef CONFIG_MMC
|
||||
#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
|
||||
#endif
|
||||
|
||||
/* Qman/Bman */
|
||||
#ifndef CONFIG_NOBQFMAN
|
||||
#define CONFIG_SYS_BMAN_NUM_PORTALS 10
|
||||
#define CONFIG_SYS_BMAN_MEM_BASE 0xf4000000
|
||||
#ifdef CONFIG_PHYS_64BIT
|
||||
#define CONFIG_SYS_BMAN_MEM_PHYS 0xff4000000ull
|
||||
#else
|
||||
#define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE
|
||||
#endif
|
||||
#define CONFIG_SYS_BMAN_MEM_SIZE 0x02000000
|
||||
#define CONFIG_SYS_BMAN_SP_CENA_SIZE 0x4000
|
||||
#define CONFIG_SYS_BMAN_SP_CINH_SIZE 0x1000
|
||||
#define CONFIG_SYS_BMAN_CENA_BASE CONFIG_SYS_BMAN_MEM_BASE
|
||||
#define CONFIG_SYS_BMAN_CENA_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
|
||||
#define CONFIG_SYS_BMAN_CINH_BASE (CONFIG_SYS_BMAN_MEM_BASE + \
|
||||
CONFIG_SYS_BMAN_CENA_SIZE)
|
||||
#define CONFIG_SYS_BMAN_CINH_SIZE (CONFIG_SYS_BMAN_MEM_SIZE >> 1)
|
||||
#define CONFIG_SYS_BMAN_SWP_ISDR_REG 0xE08
|
||||
#define CONFIG_SYS_QMAN_NUM_PORTALS 10
|
||||
#define CONFIG_SYS_QMAN_MEM_BASE 0xf6000000
|
||||
#ifdef CONFIG_PHYS_64BIT
|
||||
#define CONFIG_SYS_QMAN_MEM_PHYS 0xff6000000ull
|
||||
#else
|
||||
#define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE
|
||||
#endif
|
||||
#define CONFIG_SYS_QMAN_MEM_SIZE 0x02000000
|
||||
#define CONFIG_SYS_QMAN_SP_CENA_SIZE 0x4000
|
||||
#define CONFIG_SYS_QMAN_SP_CINH_SIZE 0x1000
|
||||
#define CONFIG_SYS_QMAN_CENA_BASE CONFIG_SYS_QMAN_MEM_BASE
|
||||
#define CONFIG_SYS_QMAN_CENA_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
|
||||
#define CONFIG_SYS_QMAN_CINH_BASE (CONFIG_SYS_QMAN_MEM_BASE + \
|
||||
CONFIG_SYS_QMAN_CENA_SIZE)
|
||||
#define CONFIG_SYS_QMAN_CINH_SIZE (CONFIG_SYS_QMAN_MEM_SIZE >> 1)
|
||||
#define CONFIG_SYS_QMAN_SWP_ISDR_REG 0xE08
|
||||
|
||||
#define CONFIG_SYS_DPAA_FMAN
|
||||
|
||||
/* Default address of microcode for the Linux FMan driver */
|
||||
#if defined(CONFIG_SPIFLASH)
|
||||
/*
|
||||
* env is stored at 0x100000, sector size is 0x10000, ucode is stored after
|
||||
* env, so we got 0x110000.
|
||||
*/
|
||||
#define CONFIG_SYS_FMAN_FW_ADDR 0x110000
|
||||
#define CONFIG_SYS_QE_FW_ADDR 0x130000
|
||||
#elif defined(CONFIG_SDCARD)
|
||||
/*
|
||||
* PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
|
||||
* about 1MB (2048 blocks), Env is stored after the image, and the env size is
|
||||
* 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080(0x820).
|
||||
*/
|
||||
#define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820)
|
||||
#define CONFIG_SYS_QE_FW_ADDR (512 * 0x920)
|
||||
#elif defined(CONFIG_MTD_RAW_NAND)
|
||||
#define CONFIG_SYS_FMAN_FW_ADDR (11 * CONFIG_SYS_NAND_BLOCK_SIZE)
|
||||
#define CONFIG_SYS_QE_FW_ADDR (12 * CONFIG_SYS_NAND_BLOCK_SIZE)
|
||||
#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
|
||||
/*
|
||||
* Slave has no ucode locally, it can fetch this from remote. When implementing
|
||||
* in two corenet boards, slave's ucode could be stored in master's memory
|
||||
* space, the address can be mapped from slave TLB->slave LAW->
|
||||
* slave SRIO or PCIE outbound window->master inbound window->
|
||||
* master LAW->the ucode address in master's memory space.
|
||||
*/
|
||||
#define CONFIG_SYS_FMAN_FW_ADDR 0xFFE00000
|
||||
#else
|
||||
#define CONFIG_SYS_FMAN_FW_ADDR 0xEFF00000
|
||||
#define CONFIG_SYS_QE_FW_ADDR 0xEFE00000
|
||||
#endif
|
||||
#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000
|
||||
#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
|
||||
#endif /* CONFIG_NOBQFMAN */
|
||||
|
||||
#ifdef CONFIG_SYS_DPAA_FMAN
|
||||
#define RGMII_PHY1_ADDR 0x1
|
||||
#define RGMII_PHY2_ADDR 0x2
|
||||
#define SGMII_CARD_AQ_PHY_ADDR_S3 0x3
|
||||
#define SGMII_CARD_AQ_PHY_ADDR_S4 0x4
|
||||
#define SGMII_CARD_AQ_PHY_ADDR_S5 0x5
|
||||
#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
|
||||
#define SGMII_CARD_PORT2_PHY_ADDR 0x1D
|
||||
#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
|
||||
#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
|
||||
#endif
|
||||
|
||||
#ifdef CONFIG_FMAN_ENET
|
||||
#define CONFIG_ETHPRIME "FM1@DTSEC4"
|
||||
#endif
|
||||
|
||||
/*
|
||||
* Dynamic MTD Partition support with mtdparts
|
||||
*/
|
||||
|
||||
/*
|
||||
* Environment
|
||||
*/
|
||||
#define CONFIG_LOADS_ECHO /* echo on for serial download */
|
||||
#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
|
||||
|
||||
/*
|
||||
* Miscellaneous configurable options
|
||||
*/
|
||||
#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
|
||||
|
||||
/*
|
||||
* For booting Linux, the board info and command line data
|
||||
* have to be in the first 64 MB of memory, since this is
|
||||
* the maximum mapped by the Linux kernel during initialization.
|
||||
*/
|
||||
#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial map for Linux*/
|
||||
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
|
||||
|
||||
#ifdef CONFIG_CMD_KGDB
|
||||
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
|
||||
#endif
|
||||
|
||||
/*
|
||||
* Environment Configuration
|
||||
*/
|
||||
#define CONFIG_ROOTPATH "/opt/nfsroot"
|
||||
#define CONFIG_BOOTFILE "uImage"
|
||||
#define CONFIG_UBOOTPATH "u-boot.bin" /* U-Boot image on TFTP server */
|
||||
#define CONFIG_LOADADDR 1000000 /* default location for tftp, bootm */
|
||||
#define __USB_PHY_TYPE utmi
|
||||
|
||||
#define CONFIG_EXTRA_ENV_SETTINGS \
|
||||
"hwconfig=fsl_ddr:ctlr_intlv=cacheline,bank_intlv=cs0_cs1;\0" \
|
||||
"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0" \
|
||||
"bootargs=root=/dev/ram rw console=ttyS0,115200\0" \
|
||||
"ramdiskfile=t1024qds/ramdisk.uboot\0" \
|
||||
"fdtfile=t1024qds/t1024qds.dtb\0" \
|
||||
"netdev=eth0\0" \
|
||||
"video-mode=fslfb:1024x768-32@60,monitor=dvi\0" \
|
||||
"uboot=" __stringify(CONFIG_UBOOTPATH) "\0" \
|
||||
"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0" \
|
||||
"tftpflash=tftpboot $loadaddr $uboot && " \
|
||||
"protect off $ubootaddr +$filesize && " \
|
||||
"erase $ubootaddr +$filesize && " \
|
||||
"cp.b $loadaddr $ubootaddr $filesize && " \
|
||||
"protect on $ubootaddr +$filesize && " \
|
||||
"cmp.b $loadaddr $ubootaddr $filesize\0" \
|
||||
"consoledev=ttyS0\0" \
|
||||
"ramdiskaddr=2000000\0" \
|
||||
"fdtaddr=d00000\0" \
|
||||
"bdev=sda3\0"
|
||||
|
||||
#define CONFIG_LINUX \
|
||||
"setenv bootargs root=/dev/ram rw " \
|
||||
"console=$consoledev,$baudrate $othbootargs;" \
|
||||
"setenv ramdiskaddr 0x02000000;" \
|
||||
"setenv fdtaddr 0x00c00000;" \
|
||||
"setenv loadaddr 0x1000000;" \
|
||||
"bootm $loadaddr $ramdiskaddr $fdtaddr"
|
||||
|
||||
#define CONFIG_NFSBOOTCOMMAND \
|
||||
"setenv bootargs root=/dev/nfs rw " \
|
||||
"nfsroot=$serverip:$rootpath " \
|
||||
"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
|
||||
"console=$consoledev,$baudrate $othbootargs;" \
|
||||
"tftp $loadaddr $bootfile;" \
|
||||
"tftp $fdtaddr $fdtfile;" \
|
||||
"bootm $loadaddr - $fdtaddr"
|
||||
|
||||
#define CONFIG_BOOTCOMMAND CONFIG_LINUX
|
||||
|
||||
#include <asm/fsl_secure_boot.h>
|
||||
|
||||
#endif /* __T1024QDS_H */
|
||||
Reference in New Issue
Block a user