diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig index 83f8f9513f..c1e762a518 100644 --- a/arch/arm/mach-sunxi/Kconfig +++ b/arch/arm/mach-sunxi/Kconfig @@ -909,27 +909,18 @@ config VIDEO_LCD_BL_PWM_ACTIVE_LOW config VIDEO_LCD_PANEL_I2C bool "LCD panel needs to be configured via i2c" depends on VIDEO_SUNXI - select CMD_I2C + select DM_I2C + select DM_I2C_GPIO ---help--- Say y here if the LCD panel needs to be configured via i2c. This will add a bitbang i2c controller using gpios to talk to the LCD. -config VIDEO_LCD_PANEL_I2C_SDA - string "LCD panel i2c interface SDA pin" +config VIDEO_LCD_PANEL_I2C_NAME + string "LCD panel i2c interface node name" depends on VIDEO_LCD_PANEL_I2C - default "PG12" + default "i2c@0" ---help--- - Set the SDA pin for the LCD i2c interface. This takes a string in the - format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. - -config VIDEO_LCD_PANEL_I2C_SCL - string "LCD panel i2c interface SCL pin" - depends on VIDEO_LCD_PANEL_I2C - default "PG10" - ---help--- - Set the SCL pin for the LCD i2c interface. This takes a string in the - format understood by sunxi_name_to_gpio, e.g. PH1 for pin 1 of port H. - + Set the device tree node name for the LCD i2c interface. # Note only one of these may be selected at a time! But hidden choices are # not supported by Kconfig diff --git a/board/sunxi/board.c b/board/sunxi/board.c index 65cb3a6fe3..4f5747c34a 100644 --- a/board/sunxi/board.c +++ b/board/sunxi/board.c @@ -47,47 +47,6 @@ #include #include -#if defined(CONFIG_VIDEO_LCD_PANEL_I2C) -/* So that we can use pin names in Kconfig and sunxi_name_to_gpio() */ -int soft_i2c_gpio_sda; -int soft_i2c_gpio_scl; - -static int soft_i2c_board_init(void) -{ - int ret; - - soft_i2c_gpio_sda = sunxi_name_to_gpio(CONFIG_VIDEO_LCD_PANEL_I2C_SDA); - if (soft_i2c_gpio_sda < 0) { - printf("Error invalid soft i2c sda pin: '%s', err %d\n", - CONFIG_VIDEO_LCD_PANEL_I2C_SDA, soft_i2c_gpio_sda); - return soft_i2c_gpio_sda; - } - ret = gpio_request(soft_i2c_gpio_sda, "soft-i2c-sda"); - if (ret) { - printf("Error requesting soft i2c sda pin: '%s', err %d\n", - CONFIG_VIDEO_LCD_PANEL_I2C_SDA, ret); - return ret; - } - - soft_i2c_gpio_scl = sunxi_name_to_gpio(CONFIG_VIDEO_LCD_PANEL_I2C_SCL); - if (soft_i2c_gpio_scl < 0) { - printf("Error invalid soft i2c scl pin: '%s', err %d\n", - CONFIG_VIDEO_LCD_PANEL_I2C_SCL, soft_i2c_gpio_scl); - return soft_i2c_gpio_scl; - } - ret = gpio_request(soft_i2c_gpio_scl, "soft-i2c-scl"); - if (ret) { - printf("Error requesting soft i2c scl pin: '%s', err %d\n", - CONFIG_VIDEO_LCD_PANEL_I2C_SCL, ret); - return ret; - } - - return 0; -} -#else -static int soft_i2c_board_init(void) { return 0; } -#endif - DECLARE_GLOBAL_DATA_PTR; void i2c_init_board(void) @@ -312,8 +271,7 @@ int board_init(void) #endif #endif /* CONFIG_DM_MMC */ - /* Uses dm gpio code so do this here and not in i2c_init_board() */ - return soft_i2c_board_init(); + return 0; } /* diff --git a/configs/Colombus_defconfig b/configs/Colombus_defconfig index 31541f898d..270bd7d351 100644 --- a/configs/Colombus_defconfig +++ b/configs/Colombus_defconfig @@ -13,15 +13,9 @@ CONFIG_VIDEO_LCD_DCLK_PHASE=0 CONFIG_VIDEO_LCD_POWER="PH27" CONFIG_VIDEO_LCD_BL_EN="PM1" CONFIG_VIDEO_LCD_BL_PWM="PH13" -CONFIG_VIDEO_LCD_PANEL_I2C_SDA="PA23" -CONFIG_VIDEO_LCD_PANEL_I2C_SCL="PA24" CONFIG_VIDEO_LCD_PANEL_EDP_4_LANE_1620M_VIA_ANX9804=y # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set -CONFIG_SYS_I2C_LEGACY=y CONFIG_SPL_SYS_I2C_LEGACY=y -CONFIG_SYS_I2C_SOFT=y -CONFIG_SYS_I2C_SOFT_SPEED=50000 -CONFIG_SYS_I2C_SOFT_SLAVE=0x00 CONFIG_SYS_I2C_MVTWSI=y CONFIG_SYS_I2C_SLAVE=0x7f CONFIG_SYS_I2C_SPEED=400000 diff --git a/configs/UTOO_P66_defconfig b/configs/UTOO_P66_defconfig index b572807308..b021b0a886 100644 --- a/configs/UTOO_P66_defconfig +++ b/configs/UTOO_P66_defconfig @@ -21,9 +21,6 @@ CONFIG_VIDEO_LCD_BL_PWM="PB2" CONFIG_VIDEO_LCD_TL059WV5C0=y # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set CONFIG_SPL_I2C=y -CONFIG_SYS_I2C_SOFT=y -CONFIG_SYS_I2C_SOFT_SPEED=50000 -CONFIG_SYS_I2C_SOFT_SLAVE=0x00 CONFIG_SYS_I2C_MVTWSI=y CONFIG_SYS_I2C_SLAVE=0x7f CONFIG_SYS_I2C_SPEED=400000 diff --git a/drivers/video/anx9804.c b/drivers/video/anx9804.c index 3037ff39b4..52b5988ba5 100644 --- a/drivers/video/anx9804.c +++ b/drivers/video/anx9804.c @@ -21,18 +21,23 @@ * This function will init an anx9804 parallel lcd to dp bridge chip * using the passed in parameters. * - * @i2c_bus: Number of the i2c bus to which the anx9804 is connected. + * @i2c_bus: Device of the i2c bus to which the anx9804 is connected. * @lanes: Number of displayport lanes to use * @data_rate: Register value for the bandwidth reg 0x06: 1.62G, 0x0a: 2.7G * @bpp: Bits per pixel, must be 18 or 24 */ -void anx9804_init(unsigned int i2c_bus, u8 lanes, u8 data_rate, int bpp) +void anx9804_init(struct udevice *i2c_bus, u8 lanes, u8 data_rate, int bpp) { - unsigned int orig_i2c_bus = i2c_get_bus_num(); - u8 c, colordepth; - int i; + struct udevice *chip0, *chip1; + int c, colordepth, i, ret; - i2c_set_bus_num(i2c_bus); + ret = i2c_get_chip(i2c_bus, 0x38, 1, &chip0); + if (ret) + return; + + ret = i2c_get_chip(i2c_bus, 0x39, 1, &chip1); + if (ret) + return; if (bpp == 18) colordepth = 0x00; /* 6 bit */ @@ -40,24 +45,23 @@ void anx9804_init(unsigned int i2c_bus, u8 lanes, u8 data_rate, int bpp) colordepth = 0x10; /* 8 bit */ /* Reset */ - i2c_reg_write(0x39, ANX9804_RST_CTRL_REG, 1); + dm_i2c_reg_write(chip1, ANX9804_RST_CTRL_REG, 1); mdelay(100); - i2c_reg_write(0x39, ANX9804_RST_CTRL_REG, 0); + dm_i2c_reg_write(chip1, ANX9804_RST_CTRL_REG, 0); /* Write 0 to the powerdown reg (powerup everything) */ - i2c_reg_write(0x39, ANX9804_POWERD_CTRL_REG, 0); + dm_i2c_reg_write(chip1, ANX9804_POWERD_CTRL_REG, 0); - c = i2c_reg_read(0x39, ANX9804_DEV_IDH_REG); + c = dm_i2c_reg_read(chip1, ANX9804_DEV_IDH_REG); if (c != 0x98) { printf("Error anx9804 chipid mismatch\n"); - i2c_set_bus_num(orig_i2c_bus); return; } for (i = 0; i < 100; i++) { - c = i2c_reg_read(0x38, ANX9804_SYS_CTRL2_REG); - i2c_reg_write(0x38, ANX9804_SYS_CTRL2_REG, c); - c = i2c_reg_read(0x38, ANX9804_SYS_CTRL2_REG); + c = dm_i2c_reg_read(chip0, ANX9804_SYS_CTRL2_REG); + dm_i2c_reg_write(chip0, ANX9804_SYS_CTRL2_REG, c); + c = dm_i2c_reg_read(chip0, ANX9804_SYS_CTRL2_REG); if ((c & ANX9804_SYS_CTRL2_CHA_STA) == 0) break; @@ -66,51 +70,51 @@ void anx9804_init(unsigned int i2c_bus, u8 lanes, u8 data_rate, int bpp) if (i == 100) printf("Error anx9804 clock is not stable\n"); - i2c_reg_write(0x39, ANX9804_VID_CTRL2_REG, colordepth); + dm_i2c_reg_write(chip1, ANX9804_VID_CTRL2_REG, colordepth); /* Set a bunch of analog related register values */ - i2c_reg_write(0x38, ANX9804_PLL_CTRL_REG, 0x07); - i2c_reg_write(0x39, ANX9804_PLL_FILTER_CTRL3, 0x19); - i2c_reg_write(0x39, ANX9804_PLL_CTRL3, 0xd9); - i2c_reg_write(0x39, ANX9804_RST_CTRL2_REG, ANX9804_RST_CTRL2_AC_MODE); - i2c_reg_write(0x39, ANX9804_ANALOG_DEBUG_REG1, 0xf0); - i2c_reg_write(0x39, ANX9804_ANALOG_DEBUG_REG3, 0x99); - i2c_reg_write(0x39, ANX9804_PLL_FILTER_CTRL1, 0x7b); - i2c_reg_write(0x38, ANX9804_LINK_DEBUG_REG, 0x30); - i2c_reg_write(0x39, ANX9804_PLL_FILTER_CTRL, 0x06); + dm_i2c_reg_write(chip0, ANX9804_PLL_CTRL_REG, 0x07); + dm_i2c_reg_write(chip1, ANX9804_PLL_FILTER_CTRL3, 0x19); + dm_i2c_reg_write(chip1, ANX9804_PLL_CTRL3, 0xd9); + dm_i2c_reg_write(chip1, ANX9804_RST_CTRL2_REG, ANX9804_RST_CTRL2_AC_MODE); + dm_i2c_reg_write(chip1, ANX9804_ANALOG_DEBUG_REG1, 0xf0); + dm_i2c_reg_write(chip1, ANX9804_ANALOG_DEBUG_REG3, 0x99); + dm_i2c_reg_write(chip1, ANX9804_PLL_FILTER_CTRL1, 0x7b); + dm_i2c_reg_write(chip0, ANX9804_LINK_DEBUG_REG, 0x30); + dm_i2c_reg_write(chip1, ANX9804_PLL_FILTER_CTRL, 0x06); /* Force HPD */ - i2c_reg_write(0x38, ANX9804_SYS_CTRL3_REG, - ANX9804_SYS_CTRL3_F_HPD | ANX9804_SYS_CTRL3_HPD_CTRL); + dm_i2c_reg_write(chip0, ANX9804_SYS_CTRL3_REG, + ANX9804_SYS_CTRL3_F_HPD | ANX9804_SYS_CTRL3_HPD_CTRL); /* Power up and configure lanes */ - i2c_reg_write(0x38, ANX9804_ANALOG_POWER_DOWN_REG, 0x00); - i2c_reg_write(0x38, ANX9804_TRAINING_LANE0_SET_REG, 0x00); - i2c_reg_write(0x38, ANX9804_TRAINING_LANE1_SET_REG, 0x00); - i2c_reg_write(0x38, ANX9804_TRAINING_LANE2_SET_REG, 0x00); - i2c_reg_write(0x38, ANX9804_TRAINING_LANE3_SET_REG, 0x00); + dm_i2c_reg_write(chip0, ANX9804_ANALOG_POWER_DOWN_REG, 0x00); + dm_i2c_reg_write(chip0, ANX9804_TRAINING_LANE0_SET_REG, 0x00); + dm_i2c_reg_write(chip0, ANX9804_TRAINING_LANE1_SET_REG, 0x00); + dm_i2c_reg_write(chip0, ANX9804_TRAINING_LANE2_SET_REG, 0x00); + dm_i2c_reg_write(chip0, ANX9804_TRAINING_LANE3_SET_REG, 0x00); /* Reset AUX CH */ - i2c_reg_write(0x39, ANX9804_RST_CTRL2_REG, - ANX9804_RST_CTRL2_AC_MODE | ANX9804_RST_CTRL2_AUX); - i2c_reg_write(0x39, ANX9804_RST_CTRL2_REG, - ANX9804_RST_CTRL2_AC_MODE); + dm_i2c_reg_write(chip1, ANX9804_RST_CTRL2_REG, + ANX9804_RST_CTRL2_AC_MODE | ANX9804_RST_CTRL2_AUX); + dm_i2c_reg_write(chip1, ANX9804_RST_CTRL2_REG, + ANX9804_RST_CTRL2_AC_MODE); /* Powerdown audio and some other unused bits */ - i2c_reg_write(0x39, ANX9804_POWERD_CTRL_REG, ANX9804_POWERD_AUDIO); - i2c_reg_write(0x38, ANX9804_HDCP_CONTROL_0_REG, 0x00); - i2c_reg_write(0x38, 0xa7, 0x00); + dm_i2c_reg_write(chip1, ANX9804_POWERD_CTRL_REG, ANX9804_POWERD_AUDIO); + dm_i2c_reg_write(chip0, ANX9804_HDCP_CONTROL_0_REG, 0x00); + dm_i2c_reg_write(chip0, 0xa7, 0x00); /* Set data-rate / lanes */ - i2c_reg_write(0x38, ANX9804_LINK_BW_SET_REG, data_rate); - i2c_reg_write(0x38, ANX9804_LANE_COUNT_SET_REG, lanes); + dm_i2c_reg_write(chip0, ANX9804_LINK_BW_SET_REG, data_rate); + dm_i2c_reg_write(chip0, ANX9804_LANE_COUNT_SET_REG, lanes); /* Link training */ - i2c_reg_write(0x38, ANX9804_LINK_TRAINING_CTRL_REG, - ANX9804_LINK_TRAINING_CTRL_EN); + dm_i2c_reg_write(chip0, ANX9804_LINK_TRAINING_CTRL_REG, + ANX9804_LINK_TRAINING_CTRL_EN); mdelay(5); for (i = 0; i < 100; i++) { - c = i2c_reg_read(0x38, ANX9804_LINK_TRAINING_CTRL_REG); + c = dm_i2c_reg_read(chip0, ANX9804_LINK_TRAINING_CTRL_REG); if ((c & 0x01) == 0) break; @@ -118,17 +122,14 @@ void anx9804_init(unsigned int i2c_bus, u8 lanes, u8 data_rate, int bpp) } if(i == 100) { printf("Error anx9804 link training timeout\n"); - i2c_set_bus_num(orig_i2c_bus); return; } /* Enable */ - i2c_reg_write(0x39, ANX9804_VID_CTRL1_REG, - ANX9804_VID_CTRL1_VID_EN | ANX9804_VID_CTRL1_EDGE); + dm_i2c_reg_write(chip1, ANX9804_VID_CTRL1_REG, + ANX9804_VID_CTRL1_VID_EN | ANX9804_VID_CTRL1_EDGE); /* Force stream valid */ - i2c_reg_write(0x38, ANX9804_SYS_CTRL3_REG, - ANX9804_SYS_CTRL3_F_HPD | ANX9804_SYS_CTRL3_HPD_CTRL | - ANX9804_SYS_CTRL3_F_VALID | ANX9804_SYS_CTRL3_VALID_CTRL); - - i2c_set_bus_num(orig_i2c_bus); + dm_i2c_reg_write(chip0, ANX9804_SYS_CTRL3_REG, + ANX9804_SYS_CTRL3_F_HPD | ANX9804_SYS_CTRL3_HPD_CTRL | + ANX9804_SYS_CTRL3_F_VALID | ANX9804_SYS_CTRL3_VALID_CTRL); } diff --git a/drivers/video/anx9804.h b/drivers/video/anx9804.h index c0fe3b393b..ea6c9f2d55 100644 --- a/drivers/video/anx9804.h +++ b/drivers/video/anx9804.h @@ -16,9 +16,10 @@ #define ANX9804_DATA_RATE_2700M 0x0a #ifdef CONFIG_VIDEO_LCD_PANEL_EDP_4_LANE_1620M_VIA_ANX9804 -void anx9804_init(unsigned int i2c_bus, u8 lanes, u8 data_rate, int bpp); +void anx9804_init(struct udevice *i2c_bus, u8 lanes, u8 data_rate, int bpp); #else -static inline void anx9804_init(unsigned int i2c_bus, u8 lanes, u8 data_rate, +static inline void anx9804_init(struct udevice *i2c_bus, u8 lanes, u8 data_rate, int bpp) {} #endif + #endif diff --git a/drivers/video/sunxi/sunxi_display.c b/drivers/video/sunxi/sunxi_display.c index da3e898829..5a21f7af66 100644 --- a/drivers/video/sunxi/sunxi_display.c +++ b/drivers/video/sunxi/sunxi_display.c @@ -901,6 +901,42 @@ static int sunxi_ssd2828_init(const struct ctfb_res_modes *mode) } #endif /* CONFIG_VIDEO_LCD_SSD2828 */ +#ifdef CONFIG_VIDEO_LCD_PANEL_I2C +static void sunxi_panel_i2c_init(struct sunxi_display_priv *sunxi_display) +{ + const char *name = CONFIG_VIDEO_LCD_PANEL_I2C_NAME; + struct udevice *i2c_bus; + int ret; + + ret = uclass_get_device_by_name(UCLASS_I2C, name, &i2c_bus); + if (ret) + return; + + if (IS_ENABLED(CONFIG_VIDEO_LCD_PANEL_EDP_4_LANE_1620M_VIA_ANX9804)) { + /* + * The anx9804 needs 1.8V from eldo3, we do this here + * and not via CONFIG_AXP_ELDO3_VOLT from board_init() + * to avoid turning this on when using hdmi output. + */ + axp_set_eldo(3, 1800); + anx9804_init(i2c_bus, 4, + ANX9804_DATA_RATE_1620M, + sunxi_display->depth); + } + if (IS_ENABLED(CONFIG_VIDEO_LCD_TL059WV5C0)) { + struct udevice *chip; + + ret = i2c_get_chip(i2c_bus, 0x5c, 1, &chip); + if (ret) + return; + + dm_i2c_reg_write(chip, 0x04, 0x42); /* Turn on the LCD */ + } +} +#else +static void sunxi_panel_i2c_init(struct sunxi_display_priv *sunxi_display) {} +#endif + static void sunxi_engines_init(void) { sunxi_composer_init(); @@ -935,27 +971,12 @@ static void sunxi_mode_set(struct sunxi_display_priv *sunxi_display, break; case sunxi_monitor_lcd: sunxi_lcdc_panel_enable(); - if (IS_ENABLED(CONFIG_VIDEO_LCD_PANEL_EDP_4_LANE_1620M_VIA_ANX9804)) { - /* - * The anx9804 needs 1.8V from eldo3, we do this here - * and not via CONFIG_AXP_ELDO3_VOLT from board_init() - * to avoid turning this on when using hdmi output. - */ - axp_set_eldo(3, 1800); - anx9804_init(CONFIG_VIDEO_LCD_I2C_BUS, 4, - ANX9804_DATA_RATE_1620M, - sunxi_display->depth); - } if (IS_ENABLED(CONFIG_VIDEO_LCD_HITACHI_TX18D42VM)) { mdelay(50); /* Wait for lcd controller power on */ hitachi_tx18d42vm_init(); } - if (IS_ENABLED(CONFIG_VIDEO_LCD_TL059WV5C0)) { - unsigned int orig_i2c_bus = i2c_get_bus_num(); - i2c_set_bus_num(CONFIG_VIDEO_LCD_I2C_BUS); - i2c_reg_write(0x5c, 0x04, 0x42); /* Turn on the LCD */ - i2c_set_bus_num(orig_i2c_bus); - } + if (IS_ENABLED(CONFIG_VIDEO_LCD_PANEL_I2C)) + sunxi_panel_i2c_init(sunxi_display); sunxi_composer_mode_set(mode, address, monitor); sunxi_lcdc_tcon0_mode_set(sunxi_display, mode, false); sunxi_composer_enable(); diff --git a/include/configs/sunxi-common.h b/include/configs/sunxi-common.h index 5d8b6052e4..c576d65efa 100644 --- a/include/configs/sunxi-common.h +++ b/include/configs/sunxi-common.h @@ -160,23 +160,6 @@ #define CONFIG_SPL_PAD_TO 32768 /* decimal for 'dd' */ #endif - -/* I2C */ -#if defined(CONFIG_VIDEO_LCD_PANEL_I2C) -/* We use pin names in Kconfig and sunxi_name_to_gpio() */ -#define CONFIG_SOFT_I2C_GPIO_SDA soft_i2c_gpio_sda -#define CONFIG_SOFT_I2C_GPIO_SCL soft_i2c_gpio_scl -#ifndef __ASSEMBLY__ -extern int soft_i2c_gpio_sda; -extern int soft_i2c_gpio_scl; -#endif -#define CONFIG_VIDEO_LCD_I2C_BUS 0 /* The lcd panel soft i2c is bus 0 */ -#define CONFIG_SYS_SPD_BUS_NUM 1 /* And the axp209 i2c bus is bus 1 */ -#else -#define CONFIG_SYS_SPD_BUS_NUM 0 /* The axp209 i2c bus is bus 0 */ -#define CONFIG_VIDEO_LCD_I2C_BUS -1 /* NA, but necessary to compile */ -#endif - /* Ethernet support */ #ifdef CONFIG_USB_EHCI_HCD