menu "SharpKey Configuration" choice BUILD_TARGET prompt "Build target" default SHARPKEY help Choose the target of the next build, SHARPKEY for the multi-host SharpKey Interface, MZ25KEY_MZ2500 for the mz25key Interface which will be used with an MZ-2500 or MZ25KEY_MZ2800 for the mz25key Interface which will be used with an MZ-2800. config SHARPKEY bool "SharpKey" help Target build for the SharpKey multi-host Interface. config MZ25KEY_MZ2500 bool "mz25key - MZ2500" help Target build for the mz25key Interface for use on an MZ-2500 config MZ25KEY_MZ2800 bool "mz25key - MZ2800" help Target build for the mz25key Interface for use on an MZ-2800 endchoice choice FEATURE_SECURITY prompt "Runtime Feature Security" default DISABLE_FEATURE_SECURITY help Choose wether to enable features in the firmware based on fuse settings or to disable the feature. config DISABLE_FEATURE_SECURITY bool "Disable feature security" help Disable the feature security, enabling all inbuilt modules of the SharpKey firmware. config ENABLE_FEATURE_SECURITY bool "Enable feature security" help Enable feature security, modules will only be available if the corresponding eFuse is set. endchoice menu "PS2 Keyboard" config PS2_HW_DATAPIN int "GPIO pin number used for the PS/2 Keyboard DATA line" range 0 46 default 14 help GPIO number (IOxx) used to connect with the PS/2 Keyboard DATA line. Some GPIOs are used for other purposes (flash connections, etc.) and cannot be used to I2C. GPIOs 35-39 are input-only so cannot be used as outputs. config PS2_HW_CLKPIN int "GPIO pin number used for the PS/2 Keyboard CLK line" range 0 46 default 13 help GPIO number (IOxx) used to connect with the PS/2 Keyboard CLK line. This pin must be interrupt capable. Some GPIOs are used for other purposes (flash connections, etc.) and cannot be used to I2C. GPIOs 35-39 are input-only so cannot be used as outputs. endmenu menu "Host Interface" menu "4Bit Strobe Input" config HOST_KDB0 int "KDB0 GPIO pin number" range 0 46 default 23 help GPIO number (IOxx) used to connect the 4bit bidirectional data bus Bit 0 with the ESP32. See schematic for actual used value. May change with revisions. config HOST_KDB1 int "KDB1 GPIO pin number" range 0 46 default 25 help GPIO number (IOxx) used to connect the 4bit bidirectional data bus Bit 1 with the ESP32. See schematic for actual used value. May change with revisions. config HOST_KDB2 int "KDB2 GPIO pin number" range 0 46 default 26 help GPIO number (IOxx) used to connect the 4bit bidirectional data bus Bit 2 with the ESP32. See schematic for actual used value. May change with revisions. config HOST_KDB3 int "KDB3 GPIO pin number" range 0 46 default 27 help GPIO number (IOxx) used to connect the 4bit bidirectional data bus Bit 3 with the ESP32. See schematic for actual used value. May change with revisions. endmenu menu "8Bit Scan Data Output" config HOST_KDO0 int "KDO0 GPIO pin number" range 0 46 default 14 help GPIO number (IOxx) used to connect the 8bit scan data output Bit 0 to the 74HCT257 IC. See schematic for actual used value. May change with revisions. config HOST_KDO1 int "KDO1 GPIO pin number" range 0 46 default 15 help GPIO number (IOxx) used to connect the 8bit scan data output Bit 1 to the 74HCT257 IC. See schematic for actual used value. May change with revisions. config HOST_KDO2 int "KDO2 GPIO pin number" range 0 46 default 16 help GPIO number (IOxx) used to connect the 8bit scan data output Bit 2 to the 74HCT257 IC. See schematic for actual used value. May change with revisions. config HOST_KDO3 int "KDO3 GPIO pin number" range 0 46 default 17 help GPIO number (IOxx) used to connect the 8bit scan data output Bit 3 to the 74HCT257 IC. See schematic for actual used value. May change with revisions. config HOST_KDO4 int "KDO4 GPIO pin number" range 0 46 default 18 help GPIO number (IOxx) used to connect the 8bit scan data output Bit 4 to the 74HCT257 IC. See schematic for actual used value. May change with revisions. config HOST_KDO5 int "KDO5 GPIO pin number" range 0 46 default 19 help GPIO number (IOxx) used to connect the 8bit scan data output Bit 5 to the 74HCT257 IC. See schematic for actual used value. May change with revisions. config HOST_KDO6 int "KDO6 GPIO pin number" range 0 46 default 21 help GPIO number (IOxx) used to connect the 8bit scan data output Bit 6 to the 74HCT257 IC. See schematic for actual used value. May change with revisions. config HOST_KDO7 int "KDO7 GPIO pin number" range 0 46 default 21 help GPIO number (IOxx) used to connect the 8bit scan data output Bit 7 to the 74HCT257 IC. See schematic for actual used value. May change with revisions. endmenu choice MOUSE_UART_CHOICE prompt "Mouse host side UART" default HOST_BITBANG_UART help Select the hardware method of sending mouse data to the host. The two possible methods are bitbang (software UART) and UART Hardware. config HOST_BITBANG_UART bool "Bitbang UART" help Use the Bitbang UART (software). config HOST_HW_UART bool "Hardware UART" help Use one of the ESP32 Hardware UART's. endchoice config HOST_RTSNI int "RTSNi GPIO pin number" range 0 46 default 35 help GPIO number (IOxx) used to connect the RTSN line with the ESP32. See schematic for actual used value. May change with revisions. config HOST_MPXI int "MPXi GPIO pin number" range 0 46 default 12 help GPIO number (IOxx) used to connect the MPX line with the ESP32. See schematic for actual used value. May change with revisions. config HOST_KDI4 int "KDI4 GPIO pin number" range 0 46 default 13 help GPIO number (IOxx) used to connect the KDI4 line with the ESP32. See schematic for actual used value. May change with revisions. endmenu menu "WiFi" config IF_WIFI_ENABLED bool "Enable WiFi connectivity" default false help Allow interface to act as an Access Point to allow external connectivity. Once connected the WiFi is intended to be used for making key mapping changes. This is an experimental feature and under development. config IF_WIFI_EN_KEY int "WiFi Enable GPIO pin number" range 0 46 default 34 depends on IF_WIFI_ENABLED help GPIO number (IOxx) used by the WiFi En switch to enable wifi connectivity. config IF_WIFI_SSID string "Default SSID in Access Point Mode" default "sharpkey" depends on IF_WIFI_ENABLED help The SSID broadcast whilst the sharpkey module advertises wireless connectivity. config IF_WIFI_DEFAULT_SSID_PWD string "Default password for initial connection to Access Point Mode" default "sharpkey" depends on IF_WIFI_ENABLED help The initial password needed to connect and logon to access point. config IF_WIFI_MAX_RETRIES int "Maximum number of connection retries." range 0 100 default 10 depends on IF_WIFI_ENABLED help Number of retries allowed for making a wireless connection with a client. config IF_WIFI_AP_CHANNEL int "Channel of the Access Point." range 0 13 default 7 depends on IF_WIFI_ENABLED help Channel use by the Access Point, default is 7. config IF_WIFI_SSID_HIDDEN int "Broadcast SSID?" range 0 1 default 0 depends on IF_WIFI_ENABLED help Broadcast the SSID (0) or hide it (1). config IF_WIFI_MAX_CONNECTIONS int "Maximum simultaneous connections." range 0 20 default 5 depends on IF_WIFI_ENABLED help Maximum number of simultaneous open connections supported. endmenu menu "Debug Options" config DEBUG_SERIAL bool "Serial debug output" default false help Enable debug output (non ESP logging) on the serial port. config DEBUG_DISABLE_KDB bool "Disable input mode actuation of the KDB data bus" default false help Disable the Host KDB input configuration step, useful feature for debugging. config DEBUG_DISABLE_KDO bool "Disable output mode actuation of the KDO strobe row" default false help Disable the Host KDO output configuration step, useful feature for debugging. config DEBUG_DISABLE_RTSNI bool "Disable input mode actuation of the RTSNi signal" default false help Disable the Host RTSNi input configuration step, useful feature for debugging. config DEBUG_DISABLE_MPXI bool "Disable input mode actuation of the MPXi signal" default false help Disable the Host MPXi input configuration step, useful feature for debugging. config DEBUG_DISABLE_KDI bool "Disable input mode actuation of the KDI4 signal" default false help Disable the Host KDI input configuration step, useful feature for debugging. endmenu config PWRLED int "GPIO pin number used for Power On and Status LED" range 0 46 default 25 help GPIO number (IOxx) used to control the Power On/Status LED. Some GPIOs are used for other purposes (flash connections, etc.) and cannot be used to I2C. GPIOs 35-39 are input-only so cannot be used as outputs. endmenu