156 lines
7.3 KiB
INI
156 lines
7.3 KiB
INI
[MiSTer]
|
|
key_menu_as_rgui=0 ; set to 1 to make the MENU key map to RGUI in Minimig (e.g. for Right Amiga)
|
|
forced_scandoubler=0 ; set to 1 to run scandoubler on VGA output always (depends on core).
|
|
ypbpr=0 ; set to 1 for YPbPr on VGA output.
|
|
composite_sync=0 ; set to 1 for composite sync on HSync signal of VGA output.
|
|
vga_scaler=0 ; set to 1 to connect VGA to scaler output.
|
|
hdmi_audio_96k=0 ; set to 1 for 96khz/16bit HDMI audio (48khz/16bit otherwise)
|
|
keyrah_mode=0x18d80002 ; VIDPID of keyrah for special code translation (0x23418037 for Arduino Micro)
|
|
vscale_mode=0 ; 0 - scale to fit the screen height.
|
|
; 1 - use integer scale only.
|
|
; 2 - use 0.5 steps of scale.
|
|
; 3 - use 0.25 steps of scale.
|
|
vscale_border=0 ; set vertical border for TVs cutting the upper/bottom parts of screen (1-399)
|
|
;bootscreen=0 ; uncomment to disable boot screen of some cores like Minimig.
|
|
;mouse_throttle=10 ; 1-100 mouse speed divider. Useful for very sensitive mice
|
|
rbf_hide_datecode=0 ; 1 - hides datecodes from rbf file names. Press F2 for quick temporary toggle
|
|
menu_pal=0 ; 1 - PAL mode for menu core
|
|
hdmi_limited=0 ; 1 - use limited (16..235) color range over HDMI
|
|
; 2 - use limited (16..255) color range over HDMI, for VGA converters.
|
|
direct_video=0 ; 1 - enable core video timing over HDMI, use only with VGA converters.
|
|
fb_size=0 ; 0 - automatic, 1 - full size, 2 - 1/2 of resolution, 4 - 1/4 of resolution.
|
|
fb_terminal=1 ; 1 - enabled (default), 0 - disabled
|
|
osd_timeout=30 ; 5-3600 timeout (in seconds) for OSD to disappear in Menu core. 30 seconds if not set.
|
|
; Background picture will get darker after double timeout
|
|
osd_rotate=0 ; Display OSD menu rotated, 0 - no rotation, 1 - rotate right (+90°), 2 - rotate left (-90°)
|
|
|
|
; 1 - enables the recent file loaded/mounted.
|
|
; WARNING: This option will enable write to SD card on every load/mount which may wear the SD card after many writes to the same place
|
|
; There is also higher chance to corrupt the File System if MiSTer will be reset or powered off while writing.
|
|
recents=0
|
|
|
|
; lastcore - Autoboot the last loaded core (corename autosaved in CONFIG/lastcore.dat) first found on the SD/USB
|
|
; lastexactcore - Autoboot the last loaded exact core (corename_yyyymmdd.rbf autosaved in CONFIG/lastcore.dat) first found on the SD/USB
|
|
; corename - Autoboot first corename_*.rbf found on the SD/USB
|
|
; corename_yyyymmdd.rbf - Autoboot first corename_yyyymmdd.rbf found on the SD/USB
|
|
;bootcore=lastcore ; uncomment to autoboot a core, as the last loaded core.
|
|
|
|
; 10-30 timeout before autoboot, comment for autoboot without timeout.
|
|
bootcore_timeout=10
|
|
|
|
; Option to load the custom font. Format is plain bitmap 8x8.
|
|
; Supported sizes of font:
|
|
; 768 bytes - chars 32-127 (only alpha + numeric)
|
|
; 1024 bytes - chars 0-127
|
|
; 1136 bytes - chars 0-141
|
|
; up to 2048 - only chars 0-141 will be used.
|
|
; if first 32 chars are empty (for sizes 1024 bytes and more) then they are skipped.
|
|
font=font/myfont.pf
|
|
|
|
; USER button emulation by keybaord. Usually it's reset button.
|
|
; 0 - lctrl+lalt+ralt (lctrl+lgui+rgui on keyrah)
|
|
; 1 - lctrl+lgui+rgui
|
|
; 2 - lctrl+lalt+del
|
|
; 3 - same as 0 (lctrl+lalt+ralt on keyrah)
|
|
reset_combo=0
|
|
|
|
; set to 1 for DVI mode. Audio won't be transmitted through HDMI in DVI mode.
|
|
dvi_mode=0
|
|
|
|
; 0 - 1280x720@60
|
|
; 1 - 1024x768@60
|
|
; 2 - 720x480@60
|
|
; 3 - 720x576@50
|
|
; 4 - 1280x1024@60
|
|
; 5 - 800x600@60
|
|
; 6 - 640x480@60
|
|
; 7 - 1280x720@50
|
|
; 8 - 1920x1080@60
|
|
; 9 - 1920x1080@50
|
|
;10 - 1366x768@60
|
|
;11 - 1024x600@60
|
|
;12 - 1920x1440@60
|
|
;13 - 2048x1536@60
|
|
;
|
|
; custom mode: hact,hfp,hs,hbp,vact,vfp,vs,vbp,Fpix_in_KHz
|
|
; video_mode=1280,110,40,220,720,5,5,20,74250
|
|
video_mode=0
|
|
|
|
; set to 1-10 (seconds) to display video info on startup/change
|
|
video_info=0
|
|
|
|
; Set to 1 for automatic HDMI VSync rate adjust to match original VSync.
|
|
; Set to 2 for low latency mode (single buffer).
|
|
; This option makes video butter smooth like on original emulated system.
|
|
; Adjusting is done by changing pixel clock. Not every display supports variable pixel clock.
|
|
; For proper adjusting and to reduce possible out of range pixel clock, use 60Hz HDMI video
|
|
; modes as a base even for 50Hz systems.
|
|
vsync_adjust=0
|
|
|
|
; If you monitor doesn't support either very low (NTSC monitors may not support PAL) or
|
|
; very high (PAL monitors may not support NTSC) then you can set refresh_min and/or refresh_max
|
|
; parameters, so vsync_adjust won't be applied for refreshes outside specified.
|
|
; These parameters are valid only when vsync_adjust is non-zero.
|
|
refresh_min=0
|
|
refresh_max=0
|
|
|
|
; These parameters have the same format as video_mode.
|
|
; You need to supply both PAL and NTSC modes if you want vsync_adjust to switch between
|
|
; predefined modes as a base. This will reduce the range of pixel clock.
|
|
;video_mode_ntsc=0
|
|
;video_mode_pal=7
|
|
|
|
; 1-10 (seconds) to display controller's button map upon first time key press
|
|
; 0 - disable
|
|
controller_info=6
|
|
|
|
; JammaSD/J-PAC/I-PAC keys to joysticks translation
|
|
; You have to provide correct VID and PID of your input device
|
|
; Examples: Legacy J-PAC with Mini-USB or USB capable I-PAC with PS/2 connectors VID=0xD209/PID=0x0301
|
|
; USB Capable J-PAC with only PS/2 connectors VID=0x04B4/PID=0x0101
|
|
; JammaSD: VID=0x04D8/PID=0xF3AD
|
|
jamma_vid=0x04D8
|
|
jamma_pid=0xF3AD
|
|
|
|
; Disable merging input devices. Use if only player 1 works.
|
|
; Leave no_merge_pid empty to apply this to all devices with the same VID.
|
|
;no_merge_vid=0x045E
|
|
;no_merge_pid=0x028E
|
|
|
|
; Speeds in sniper/non-sniper modes of mouse emulation by joystick
|
|
; 0 - (default) - faster move in non-sniper mode, slower move in sniper mode.
|
|
; 1 - movement speeds are swapped.
|
|
sniper_mode=0
|
|
|
|
; Uncomment following option if you don't want to see a second line for long file names in listing.
|
|
;browse_expand=0
|
|
|
|
; 0 - disable MiSTer logo in Menu core
|
|
logo=1
|
|
|
|
; Custom shared folder for core supporting this feature (currently minimig and ao486 only)
|
|
; Can be relative to core's home dir or absolute path.
|
|
; Path must exist before core start to use it, or it will fail.
|
|
; Make sure USB device is mounted before use shared folder on USB!
|
|
shared_folder=
|
|
|
|
; Custom aspect ratio
|
|
;custom_aspect_ratio_1=16:10
|
|
;custom_aspect_ratio_2=1:1
|
|
|
|
; use specific (VID/PID) mouse X movement as a spinner and paddle. Use VID=0xFFFF/PID=0xFFFF to use all mice as spinners.
|
|
; spinner_throttle with base value 100 gives one spinner step per one tick. Higher value makes spinner slower.
|
|
; Lower than 100 makes spinner faster. Negative value gives opposite direction.
|
|
;spinner_vid=0x1BCF
|
|
;spinner_pid=0x0005
|
|
;spinner_throttle=-50
|
|
|
|
; Default filters for video scaler and audio. Paths must be relative to scaler/audio filter folder without leading slash.
|
|
;vfilter_default=LCD Effects/LCD_Effect_07.txt
|
|
;afilter_default=LPF2000_3tap.txt
|
|
|
|
; Defines internal joypad mapping from virtual SNES mapping in main to core mapping
|
|
; Set to 0 for name mapping (jn) (e.g. A button in SNES core = A button on controller regardless of position on pad)
|
|
; Set to 1 for positional mapping (jp) (e.g. A button in SNES core = East button on controller regardless of button name)
|
|
gamepad_defaults=0
|